12360

Icom IC-756PRO Manual

76
Zoom out
Zoom in
Previous page
1/84
Next page
11
74
MAINTENANCE
■ Troubleshooting
The following chart is designed to help you correct
problems which are not equipment malfunctions.
If you are unable to locate the cause of a problem or
solve it through the use of this chart, contact your near-
est Icom Dealer or Service Center.
PROBLEM POSSIBLE CAUSE SOLUTION REF.
POWER
Power does not come on
when the [POWER] switch
is pushed.
•DC power cable is improperly connected.
•Fuse is blown.
•Reconnect the DC power cable correctly.
•Check for the cause, then replace the fuse with
a spare one.
(Fuses are installed in the DC power cable and
the internal PA unit.)
p. 17
p. 75
RECEIVE
No sound comes from the
speaker.
•Volume level is too low.
•The squelch is closed.
•The transceiver is in the transmitting condition.
•Rotate [AF] clockwise to obtain a suitable
listening level.
•Rotate [RF/SQL] to 10 o’clock position to open
the squelch.
•Push [TRANSMIT] to receive or check the
SEND line of an external unit, if desired.
p. 2
p. 3
p. 2
TRANSMIT
Transmitting is impossi-
ble.
•The operating frequency is not set to a ham
band.
•Set the frequency to a ham band. p. 24
Sensitivity is low. •The antenna is not connected properly.
•The antenna for another band is selected.
•The antenna is not properly tuned.
•The attenuator is activated.
•Reconnect to the antenna connector.
•Select an antenna suitable for the operating
frequency.
•Push [TUNER] for 2 sec. to manually tune the
antenna.
•Push [ATT] one or more times to select “ATT
OFF.”
—
pgs. 5,
45
p. 48
p. 5
Receive audio is distorted. •The operating mode is not selected correctly.
•PBT function is activated.
•Noise blanker function is activated.
•Preamp is activated.
•The noise reduction is activated and the [NR]
control is set too far clockwise.
•Select a suitable operating mode.
•Push [PBT CLR] for 2 sec. to reset the function.
•Push [NB] to turn the function OFF.
•Push [P.AMP] once or twice to turn the function
OFF.
•Set the [NR] control for maximum readability.
p. 26
p. 26
p. 27
p. 5
p. 27
The [ANT] switch does not
function.
•The antenna switch has not been activated. •Set the antenna switch in set mode to “Auto” or
“Manual.”
p. 45
SCAN
Programmed scan does
not stop.
•Squelch is open.
•[RF/SQL] is assigned to RF gain control and
squelch is open.
•Set [RF/SQL] to the threshold point.
•Reset [RF/SQL] control assignment and set it to
the threshold point.
p. 3
pgs.
3, 68
Output power is too low. •[RF POWER] is set too far counterclockwise.
•[MIC GAIN] is set too far counterclockwise.
•The antenna for another band is selected.
•The antenna is not properly tuned.
•Rotate [RF POWER] clockwise.
•Set [MIC GAIN] to a suitable position.
•Select an antenna suitable for the operating
frequency.
•Push [TUNER] for 2 sec. to manually tune the
antenna.
p. 3
p. 2
p. 5
p. 48
No contact possible with
another station.
•RIT or ∂TX function is activated.
•Split frequency function and/or dualwatch are
activated.
•Push [RIT] or [∂TX] to turn the function OFF.
•Push [SPLIT] and/or [DUALWATCH] to turn the
function OFF.
p. 6
pgs. 7
31, 32
Transmitted signals are
distorted.
•[MIC GAIN] is set too far clockwise. •Set [MIC GAIN] to a suitable position. p. 2
Repeater cannot be
accessed.
•Split frequency function is not activated.
•Programmed subaudible tone frequency is
wrong.
•Push [SPLIT] to turn the function ON.
•Reset the frequency using set mode.
p. 7
p. 46
Programmed scan does
not start.
•The same frequencies have been programmed
in scan edge memory channels P1 and P2.
•Program different frequencies in scan edge
memory channels P1 and P2.
p. 52
Memory scan does not
start.
•2 or more memory channels have not been
programmed.
•Program 2 or more memory channels. p. 52
Select memory scan does
not start.
•2 or more memory channels have not been
designated as select channels.
•Designate 2 or more memory channels as select
channels for the scan.
pgs. 51,
59
… 76 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-756PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-756PRO in the language / languages: English as an attachment in your email.

The manual is 2,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info