670163

Icom IC-7300 Manual

135
Zoom out
Zoom in
Previous page
1/173
Next page
14-4
MAINTENANCE
14
Resetting
Occasionally, erroneous information may be
displayed. This may be caused by static electricity or
by other factors.
If this problem occurs, turn OFF the transceiver. After
waiting a few seconds, turn ON the transceiver.
If the problem still exists, perform a Partial reset as
described to the right.
If the problem still exists after a Partial reset, perform
an All reset as described to the right.
NOTE: An All reset clears all data and returns all settings
to their factory defaults. Save memory channel content,
setting status, and so on, onto an SD card before the All
reset. (p. 8-4)
After performing the partial reset
A Partial reset resets operating settings to their default
values (VFO frequency, VFO settings, menu contents)
without clearing the items listed below:
• Memory channel contents (Section 9)
• MY Call (p. 13-5)
• Memory Keyer (p. 4-19)
• RTTY memory (p. 4-24)
• User Band Edge (p. 3-7)
• REF Adjust (p. 13-4)
• Fixed Edges (p. 5-7)
After performing the All reset
All reset clears all data and returns all settings to their
factory defaults.
Memory channel contents, lter setting and so on
will all be cleared, so you will need to rewrite your
operating settings, unless you have a backup.
When you cannot enter the Set mode
If a touch screen operation error or an unexpected
operation occurs, you cannot enter the Set mode. In
that case, perform the All reset as described below:
While holding down
CLEAR
and
V/M
, push
.
D Partial reset
1. Open the RESET screen.
MENU
» SET > Others > Reset
2. Touch “Partial reset.”
• The conrmation screen is displayed.
3. Touch [ Yes].
L After the resetting, the default VFO mode screen is
displayed.
D All reset
1. Open the RESET screen.
MENU
» SET > Others > Reset
2. Touch “All reset.”
• The conrmation screen is displayed.
3. Touch [NEXT].
4. After carefully reading the displayed message,
touch [YES] to perform the All reset.
L After the resetting, the default VFO mode screen is
displayed.
… 135 …


Need help? Post your question in this forum.

Forumrules
1

Forum

icom-ic-7300

Reset search

  • is there available a wiring pictorial chart for the small internal ic-7300 coaxial jumper cables?
    ie: from the RF unit to the PA board? tnx Sam in Alabam KF4TXQ Submitted on 2-1-2022 at 06:09

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7300 in the language / languages: English as an attachment in your email.

The manual is 24,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info