511737
15
Zoom out
Zoom in
Previous page
1/212
Next page
Operator information panel
Reset button: Press this button to reset the server and run the power-on self-test
(POST). You might have to use a pen or the end of a straightened
paper clip to press the button.
System-error LED: When this LED is lit, it indicates that a system error has occurred.
An LED on the diagnostic LED panel on the side of the operator
information panel is also lit to help isolate the error (see “Light path
diagnostics” on page 18).
USB connector: You can connect a USB device to this connector.
Release latch: Press this latch to release the operator information panel to access
the light path diagnostics LED panel.
Information LED: When this LED is lit, it indicates that a noncritical event has
occurred (see “Light path diagnostics” on page 18).
Locator LED: Use this blue LED to visually locate the server if it is in a location
with numerous other servers. A locator LED is also on the rear of
the server. You can use the Management Processor Assistant
(MPA) in IBM Director to cause this LED to be lit, off, or flashing
(see the User’s Guide on the IBM xSeries Documentation CD for
more information). If the server is connected to an RXE-100
Remote Expansion Enclosure, pressing the Locate button on the
enclosure causes this LED to be lit.
Note: This LED flashes while the server is being turned on or
restarted, and turns off when POST is complete.
SCSI activity LED: When this LED is lit, it indicates that there is activity on the SCSI
bus.
CD-ROM drive activity LED: When this LED is lit, it indicates that the CD-ROM
drive is in use.
Diskette drive activity LED: When this LED is lit, it indicates that the diskette drive
is in use.
Hard disk drive activity LED: When this LED is flashing, it indicates that the
associated hard disk drive is in use.
Hard disk drive status LED: When this LED is lit continuously, it indicates that the
associated hard disk drive has failed. The interpretation of a flashing status LED
depends on the SCSI controller that is connected to the hot-swap drive, as follows:
v When the drive is connected to the integrated SCSI controller with RAID
capabilities, a flashing status LED indicates that the drive is a secondary drive in
a mirrored pair and the drive is being synchronized.
v When the drive is connected to an optional ServeRAID controller, a slowly
flashing (one flash per second) status LED indicates that the drive is being
rebuilt. When the LED is flashing rapidly (three flashes per second), it indicates
that the controller is identifying the drive.
Hard disk drive filler panels: A filler panel and air baffle is used to cover empty
hard disk drive bays. A filler panel and air baffle must be installed in each empty
bay to ensure proper system cooling. Your server comes with five filler panels and
air baffles installed, and one completely empty bay.
Chapter 1. Introduction 5
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ibm X-series 365 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ibm X-series 365 in the language / languages: English as an attachment in your email.

The manual is 14,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info