521906
6
Zoom out
Zoom in
Previous page
1/6
Next page
10 11
7. House Security Code Settings
Unless the factory settings of the i.onik
®
Alarmsystem Smart Panel have been altered, the House
Security Code will NOT need to be changed.
However, if the settings on the Smart Panel have been altered, or need to be altered to solve the pro-
blem of the Smart Panel and sensors activating intermittently (or not working at all) or interference
with other systems, then the House Security Code on all system modules (sensors and sirens), will
also need to be changed.
House Security Code Settings can be altered as follows:
• There are 4 jumpers or dip-switches on each device.
Remove the battery compartment cover then toggle the dip switch contacts to change the House
Security Code.
If the dip switch is up it is ON, if it is down it is OFF. Default code on the Auto Dialler is with all the
dip switches ON (up).
To ensure the system works correctly, make sure the jumpers on the Smart Panel and all other
system modules (sensors and sirens) match exactly.
8. Maintenance
The product may be cleaned with a soft damp cloth and then wiped dry. Do not use abrasive, solvent
based or aerosol cleaners as this may damage and/or discolour the product. Do not allow water to
enter or attempt to clean inside the unit.
9. Batteries
Do not allow the batteries to corrode or leak as this may cause permanent damage to the product.
Take care to insert the batteries with the correct polarity as shown inside the battery compartments.
Do not mix new and old batteries or different types of batteries. Do not use rechargeable batteries.
At the end of their useful life the batteries should be disposed of via a suitable recycling centre. Do
not dispose of with your normal household waste. DO NOT BURN.
10. Alarm System Limitations
Even the most advanced alarm systems cannot guarantee 100 % protection against burglary or
environmental problems. All alarm systems are subject to possible compromise or failure-to-warn
for a variety of reasons.
Please note that you may encounter problems with your system if:
The Smart Panel is not placed within hearing range of persons sleeping or remote parts of the
premises.
• The sensors are placed behind doors or other obstacles.
• Intruders gain access through unprotected points of entry (where sensors are not located).
Intruders have the technical means of bypassing, jamming, or disconnecting all or part of the system.
• The power to the sensors is inadequate or disconnected.
The sensors are not located in proper environmental/temperature conditions i.e. too close to a heat
source.
Note:
Inadequate maintenance is the most common cause of alarm failure; therefore, test your
system at least once per week to be sure the sensors and sirens are working properly.
Although having an alarm system may make you eligible for reduced insurance premiums,
the system is no substitute for insurance.
Jumpers for house security
code
- Smart Panel
- Each sensor
Default house code: 1: ON, 2: ON, 3: ON, 4: ON
*Jumper: ON = Plugged, OFF = Pull Out
Dip-Switches for house
security code
- Key Fob Remote
Default house code: 1: ON, 2: ON, 3: ON, 4: ON
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for I-onik WS-110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of I-onik WS-110 in the language / languages: English, German as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info