521852

I-onik TP8-1000 Manual

18
Zoom out
Zoom in
Previous page
1/40
Next page
36 37
4-1-1 WI-FI Connection
Click the shortcut on the main screen, select “Internet Connection
Manager”, click “WI-FI setting”, then enter the WI-FI setting screen,
now select “WI-FI” and activate it.
After WI-FI has opened, it will automatically search for wireless net-
work, this shows on the menu, now click wireless network, enter the
password screen, and now input the password and connect. Seconds
later, the system will connect to wireless network automatically.
!
When WI-FI is open, this will make the machine use 25 %
more power. When not using WI-FI, please turn it off to
extend the battery life.
4-2 Ethernet Setting
Using the Ethernet card (USB-RJ45) when connecting to the Internet.
There are two requirements needed to use USB-RJ45 to connect to
the Internet, and these are detailed below:
1. ADSL account and password are set up correctly on router.
2. USB-RJ45 network card is the model which is supported by this
device.
Models supported are listed below:
AX88772/AX88772a/AX88772B/AX88178/AX88760/QF9700/
SR9600/MCS7830/MCS7832/MCS7730
Steps for Internet Connection:
First connect the network cable to the USB Ethernet card, then insert
the USB OTG cable which is meant for this device into USB Ethernet
card and the other end into USB port of the device.
Notes:
1. First close the WI-FI network, only one network can be used,
otherwise there will be errors.
2. This device will automatically detect the USB Ethernet card and
switch on the “Ethernet”. There will now be a network icon in the
status column.
3. Wait a moment, as this device will try to connect to Internet
automatically. If the router and the DHCP service are already
open, and the netgate, DNS and relevant settings have been
applied, then the device will connect to the Internet automatically.
(The Ethernet card function must be selected already).
4. If the device fails to connect, usually this is because the settings
in the router are not correct.
You can set the parameters in the device as follows:
a. Enter setting/Ethernet setting, select and open Ethernet.
Enter conguration information, choose “static IP setting”, then
enter the static IP setting screen (the default setting is auto-
matic aquiring IP. Usually, automatic aquiring IP is ne for
everything, but some companies‘ routers will use specied IPs,
not allowing automatic aquiring IP, it depends on router
settings, therefore static IP needs to be used at this time).
b. There is no need to ll in the Ethernet card device and physical
address. The machine will automatically detect this, after
successfully connecting the Ethernet.
In the IP address column, enter the IP address, the default
usually being 192.168.1.1xx.
c. In “subnet mask”, enter network segment mask, the default is
255.255.255.0.
d. In the “DNS server”, enter your local network service provider‘s
DNS server IP. A different location has a different DNS server IP
- if you are unsure, you can search by Google.
e. Enter the gateway in the „default gateway”. The general default
is 192.168.1.1 (you can check the router‘s manual for conrma-
tion). It must be set to the same as the router; otherwise
connection will be shown, however cannot connect to the
Ethernet.
f. Finally, click the lower right corner of the “Save” button, then
select Save. The system will automatically connect after saving,
then you can use the Ethernet.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for I-onik TP8-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of I-onik TP8-1000 in the language / languages: English, German as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info