675905

Hyundai 57381 - HYCH1500E-2 Manual

35
Zoom out
Zoom in
Previous page
1/40
Next page
35
Issue
Possible causes
Possible corrective actions
STARTING DIFFICULTY
NORMAL SPARK
ISSUE WITH FUEL SYSTEM
Poor fuel supply.
1.
No fuel in fuel system, fuel tap
closed.
2.
Fuel cap air vent blocked.
3.
Fuel tap blocked.
Fuel supply normal.
4.
Dirty or stale fuel.
5.
Water in fuel.
6.
Incorrect fuel.
Poor fuel supply.
1.
Fill with fuel – open fuel tap.
2.
Clear blocked air vent.
3.
Clear blockage.
Fuel supply normal.
4, 5 & 6. Clear fuel from system and
refill with fresh fuel.
STARTING DIFFICULTY
NORMAL FUEL
ISSUE HT LEAD/SPARK PLUG
Normal spark from HT lead.
1.
Carbon build up on spark plug.
2.
Electrodes badly burnt/damaged.
3.
Incorrect spark plug gap.
No spark at HT lead.
4.
HT lead damaged.
5.
Ignition coil damaged.
6.
Gap between ignition coil and
flywheel to big.
Normal spark from HT lead.
1.
Clean carbon build up.
2.
Replace spark plug.
3.
Adjust the spark plug gap.
No spark at HT lead.
4.
Replace HT lead.
5.
Replace Ignition coil.
6.
Adjust gap.
STARTING DIFFICULTY
(ELECTRIC)
Battery connection.
1.
Loose or incorrect battery
connections.
2.
Battery not charged.
Battery connection.
1.
Check polarity and tighten
connections.
2.
Remove battery from machine and
recharge.
MACHINE’S WHEELS TRACK LEFT
OR RIGHT WHILE BEING TOWED
1. Low tyre pressures. 1. Inflate tyres.
THE SHREDDER DOES NOT
SHRED PROPERLY. THE WOOD IS
NOT PULLED INTO THE MACHINE
BY ITSELF.
THE CHIPS DO NOT HAVE THE
SAME SIZE.
1.
The blades are worn too much.
2.
The diameter of the branches in-
serted into the machine are larger
than 100 mm for HYCH1500E-2 or
70mm for HYCH7070[E]-2
3.
The gap between the fixed blade
and the counter-blade is too large,
the correct gap is ½ mm
1.
Change or sharpen the blades and
counter-blade.
Note that the blades are sharpened
on both edges so they can be re-
versed.
2.
Shut the engine off and remove the
branch that is too thick.
3.
Adjust the gap between the blade
and the counter-blade in the slots
THE ENGINE WILL NOT START OR
TURN BECAUSE THE ROTOR IS
JAMMED.
1. The diameter of branches is too
big. There are unacceptable materials
such as stones or metal in the input
tube. A length of branch remains in
the rotor after the engine was last
stopped.
Shut off the engine, remove the spark
plug cap. NEVER under any circum-
stances use your hands to remove
stuck wood.
Reduce size of wood to 100 mm for
HYCH1500E-2 or 70mm for HY-
CH7070[E]-2 or less.
Use a piece of wood to turn the rotor
to remove the material from the rotor
and input tube. If necessary, remove
the cap of the bearing housing and
rotate the rotor axle with a spanner.
If necessary, remove the input or out-
put tube to get access to the rotor.
Check the sharpness of all blades,
have them sharpened or replace as
required.
Make sure all blade bolts are properly
tightened.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hyundai 57381 - HYCH1500E-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hyundai 57381 - HYCH1500E-2 in the language / languages: English as an attachment in your email.

The manual is 3,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info