Manual Hyundai 57051 (page 6 of 15) (English, German, Dutch, French, Polish)

675891

Zoom out

Zoom in

1/15

HYUNDAI

10 11

ENGLISH

- before checking, cleaning or maintaining the

appliance;

- after touching a strange object. Immediately

check the appliance for damage and repair if

necessary;

- when the appliance starts to vibrate

abnormally (check immediately).

WARNING! This device produces an

electromagnetic field during operation.

This field may interfere in certain

circumstances with active or passive

medical implants. To reduce the risk of

serious or fatal injury, we recommend

that persons with medical implants

consult their physician and the medical

implant manufacturer before using this

device.

ELECTRICAL SAFETY

Always check that the power supply

corresponds to the voltage on the

rating plate.

• For safe use, connect the appliance to an

earth leakage switch of max. 30 mA.

DESCRIPTION (FIG. A)

Your lawnmower has been designed for domestic

lawn mowing. Not suitable for professional use.

1. Motor housing

2. Lower handle bar

3. Upper handle bar

4. Locking knob

5. Cable holder

6. Cable clip

7. Rear wheel

8. Front wheel

9. Switch box

10. On/Off switch

11. Grass box

12. Lock-off button

Package contents

The package contains the following parts:

Lawnmower

Grass bag

2 cable clips

2 knobs and screws

Hook

Manual

Safety warning

Guarantee and service

Mounting the handle bar (fig. B)

• Fix the lower handle bars (2) into the unit body

with screws and washers.

• Slide the cable holder (5) onto the upper

handle (3).

• Position the upper handle (3) over the lower

handle (2) and align the holes. Push through

the two locking knobs (4). Screw on the nuts

and hand tighten. Never use a spanner or any

other tool to tighten them.

• Clamp the cable to the lower handle with the

cable clip (6).

Installing the grass collector

• Align the holes in the lower part of the grass

box with the lugs in the upper part, press the

parts together.

• Use the clips to fix the grass box.

Placing the grass box

• Lift the flap at the rear of the mower

• Align the mounting holes on the grass collector

with the notches on the mower.

• Push the container into the mower until it

clicks into place.

Removing the grass box

• Lift the lid

• Raise the grass box and pull the grass box out

of the mower.

Mounting the wheels

• Place the wheel on the shaft of the motor

housing.

• Place the washer and insert the locking pin

through the hole of the shaft, use the plastic

hook to bend the locking pin to lock the wheel.

• Align the holes and place the wheel cap.

• Mount the other wheels in the same way.

Setting the cutting heights (fig. C)

To obtain the desired cutting height, the front and

rear axles are repositioned on the underside of

the mower.

Warning! Disconnect the mower from

the power supply and ensure the blade

has stopped coasting before adjusting

the height.

• Lift the mower.

• Pull/push the wheel to the front of the mower.

• Raise/lower the wheel.

• Allow the wheel to lock in position.

• Repeat for the other wheels.

Make sure that all wheels are located

in the same cutting height position.

INSTRUCTIONS FOR USE

Warning! Before connecting to the

mains supply, always check the switch

is in off position. Connect the plug into

the RCD protected power supply.

• Connect the appliance to a suitable extension

cord.

• Fit the extension cord (socket end of cord)

through the loop and secure over the hook

before connecting the plug.

• Hold the appliance with both hands.

• Keep the appliance away from hard objects

and plants.

• When working long grass proceed layer for

layer. First set the appliance to the maximum

mowing height, then to a lower mowing height.

• Only use the appliance for working dry grass.

• Empty the grass bag after each use.

Switching on (fig. D)

• Press the safety button (12) on the combined

switch firstly and keep it down and pull the

switch lever (10) at one time. The motor starts

and you can release the safety button.

Switching off

• Release the switch lever (10).

CLEANING AND MAINTENANCE

The machine does not require any special

maintenance.

• Regularly clean the ventilation slots.

• Remove grass and dirt from the grass bag

after each use.

Before performing maintenance to the

appliance, always unplug the

appliance.

Cleaning the cutting mechanism

The cutting mechanism must be cleaned after

each use.

• Remove large dirt particles using a soft brush.

• Clean the cutting mechanism using a soft

cloth.

• Apply a few drops of oil to the cutting

mechanism to avoid oxidation.

Replacing the blade (fig. E)

Wear working gloves

Regularly check the condition of the blade and the

attachment. When the blade is worn, it must be

replaced.

When the lawnmower vibrates excessively, it

indicates an unbalanced blade or a knife that is

bent by impact force. In this case, repair or

replace the knife.

Unbalanced blades will cause the lawn

mower to vibrate violently-risk of

accident!

• Use a 35 mm spanner to unscrew the plastic

nut in anticlockwise and remove the blade to

replace it by a new one.

• Tighten the plastic nut in clockwise direction.

TECHNICAL DATA 57051

Mains voltage V 230-240

Mains frequency Hz 50

Power input W 1,000

No-load speed min

-1

3,500

Cable length cm 35

Cutting width cm 32

Cutting height cm 20-35-50

Grass box l 25

Weight kg 8.5

NOISE AND VIBRATION

Noise emission values measured according to

relevant standard. Typically the A-weighted sound

pressure level of the machine is 81 dB(A).

Uncertainty K = 3.0 dB(A).

The noise level when working can exceed 96 dB(A).

Wear hearing protection!

Vibration total values (triax vector sum) measured

according to relevant standard.

Vibration emission value a w = 2.5m/s

Uncertainty K = 1.5 m/s

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hyundai 57051 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 0,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hyundai 57051 Manual

Product: