675879

Hyundai 56477 Manual

7
Zoom out
Zoom in
Previous page
1/19
Next page
HYUNDAI
12 13
ENGLISH
screws or electrical boxes as they may damage the sanding
plate.
Emptying the dust bag
The dust bag must be emptied and cleaned regularly. Empty the
dust bag when it is half full and also clean the inside. Regular
emptying and cleaning of the dust bag is important. Due to lack of
maintenance, the suction power will decrease. The dust will then
come out through the sanding disc instead of being sucked into the
bag.
• Turn off and disconnect the tool from the power supply.
• The bag has a seam sealed by a plastic clip. Open the plastic
clip and empty the dustbag.
• Clean the bag and close it.
CLEANING AND MAINTENANCE
The machine does not require any special maintenance.
• Regularly clean the ventilation slots.
Before performing maintenance to the machine, always
unplug the machine.
TECHNICAL DATA 56477
Mains voltage V 230-240
Mains frequency Hz 50
Power input W 750
No load speed min
-1
1000-1850
Diameter sanding plate mm 225
Weight kg 4,3
NOISE AND VIBRATION
Typically the A-weighted sound pressure level of the machine is
83.1 dB(A). Uncertainty K = 3 dB(A).
The noise level when working can exceed 94.1 dB(A).
Wear hearing protection!
Vibration emission value a
h
= 1.171 m/s
2
Uncertainty K = 1.5 m/s
2
.
The declared vibration total value was measured by a standard
test method and may be used for comparing one tool with another.
The declared total vibration value can also be used in a preliminary
exposure estimate .
Warning
The vibration emission during actual use of the machine
tool can differ from the declared value depending on the
way the tool is used.
Identifying the safety measures to protect the operator
is essential, these are based on an exposure estimation
in the actual conditions of use (considering all operating
cycle parts such as the times when the tool is on and off
and when it’s running as well as its starting time).
Changing the brush
• Remove abrasive pad (see “Assembly and changing of the
abrasive discs”).
• Use a Phillips screwdriver to remove the six retaining screws
• Then remove the brush.
• Place the new brush in the housing and install it using the six
retaining screws.
• Replace the abrasive pad.
USE
Wear a protective mask. Harmful and toxic dust may be
produced when using the sander. This dust can interfere
dangerously with your and others health. Kindly always
wear a protection mask against dust when using this
product. Keep people and animals away from the work
area when the device is running.
The sander has a special sanding head: the head can rotate in
multiple directions, allowing the abrasive pad to adjust to the work
surface. This enables the user to sand the top, middle and bottom of
a wall or ceiling joint without changing its position.
How to hold the sander
The sander should be held with both hands on the main tube.
The hands may be placed anywhere along the main tube for best
application.
Keep the hands on the main tube. Do not place the hands
in the area around the sanding head. The sanding head
swivels in multiple directions and could jam your hand.
Starting and stopping
Always check that the power supply corresponds to the
voltage on the rating plate and that the sander switch is
OFF.
• Plug it into the socket
• Press and hold the on/off switch (2) to switch on the machine.
When you release the on/off switch, the machine is switched off.
You can lock the on/off switch by pressing the on/off switch and
then the lock button (3). The switch lock can be released by
pressing the on/off switch.
Speed adjustment
This sander is equipped with adjustable speed. The speed can be
controlled with the speed control (1). A higher speed should be used
for leveling and removal. A lower speed can be used for precise
renement.
Sanding
Place the correct sanding disc for the surface to be sanded (ceiling,
corner of the ceiling, different parts of a wall).
When sanding a wall or ceiling, use a ladder to reach the area to be
scoured.
Sanding tips
• Place the sander against the working surface with suitable
strength.
• Apply additional pressure for a stronger removal and reduce the
pressure for a smoother and more accurate finish.
• Apply enough pressure to keep the sanding plate flat against the
wall surface. However, excessive pressure can cause rubbing
marks or even irregularities on the worked surface.
• Keep the sander in constant motion while holding the sanding
plate in contact with the surface to be sanded.
• Use a steady, stable sweeping motion, balancing strength well.
Irregular movements and even stopping on the working surface
may create traces and irregularities.
• Avoid moving the sanding plate against objects, such as nails,
GUARANTEE
Refer to the enclosed guarantee conditions for the terms and
conditions of guarantee.
ENVIRONMENT
Disposal
Your product, accessories and packaging should be sorted for
environmental-friendly recycling.
Only for EC countries
Do not dispose of power tools into domestic waste. According to the
European Guideline 2002/96/EC for Waste Electrical and Electronic
Equipment and its implementation into national right, power tools
that are no longer usable must be collected separately and disposed
of in an environmentally friendly way.
Subject to change; specications can be changed without further
notice.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hyundai 56477 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hyundai 56477 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info