675856
4
Zoom out
Zoom in
Previous page
1/9
Next page
HYUNDAI
6 7
ENGLISH
The package contains the following parts:
Jigsaw
Saw blade
Dust extraction connection adapter
Allen key
Instruction manual
Safety warnings
Guarantee and service
Mounting saw blades (fig. B)
The opening in the saw blade holder (4) must be
clean and free from saw dust.
Loosen the set screws (10).
Slide the saw blade up to the stop in the saw
blade holder (4). Make sure that the back of
the saw blade engages in the slot of the guide
roller (11).
Tighten the set screws (10) firmly.
The set screws (10) may loosen during
use by vibration and damage the saw
blade.
Regularly check that the saw blade is
fastened firmly and if necessary fasten
the set screws. Only carry out this
inspection when the machine has been
switched off, the plug has been
removed from the wall socket and the
saw blade has come to a stand still!
Sharp saw blades produce the best
result. Replace worn saw blades on
time by new ones. Remember that
continuous use of worn saw blades
reduces the accuracy of the machine
and may lead to overloading the motor
Cutting of mitre angles (fig. C)
The max. mitre angle to the left/right is 45°.
Loosen the set screws (11).
Tilt the shoe (5) to the required mitre angle.
Tighten the set screws (11) firmly.
Switching on and off (fig. D+E)
To switch on the machine press the on/off
switch (1).
To switch off the machine, release the on/off
switch (1).
To switch the machine to continuous mode,
you keep the on/off switch (1) fully
pressed and simultaneously press the lock
button (2). And subsequently release
the on/off switch.
To switch off continuous mode, press the on/
off switch (1) again.
JIGSAW
56310
WARNING
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result in
electric shock, re and/or serious
injury. Save all warnings and
instructions for future reference.
SAFETY WARNINGS
When using the machine, always observe the
enclosed safety warnings as well as the additional
safety warnings.
The following symbols are used throughout this
manual:
Denotes risk of personal injury or
damage to the machine.
ADDITIONAL SAFETY INSTRUCTIONS FOR
JIGSAWS
Make sure that the saw blade is mounted
correctly before use.
Make sure that, when in use, the guard is
pressed down as far as possible.
Never load the machine so much that the
motor is coming to a standstill.
Never try to brake the saw blade after the
machine has been switched off.
Use original accessories only.
ELECTRICAL SAFETY
Always check that the power supply
corresponds to the voltage on the
rating plate.
DESCRIPTION (fig. A)
Your jigsaw has been designed for sawing wood,
metal and plastics.
1. On/off switch
2. Lock button
3. Safety guard
4. Saw blade holder
5. Shoe
6. Saw blade
7. Allen key holder
8. Dust extraction connection
9. Dust extraction connection adapter
GARANTIE
Voor de garantiebepalingen wordt verwezen naar
de bijgevoegde garantievoorwaarden.
MILIEU
Verwerking
Uw product, accessoires en verpakking moet
worden gesorteerd voor milieuvriendelijke
verwerking.
Werp elektrisch gereedschap niet bij het huisvuil.
Volgens de Europese Richtlijn 2002/96/EG voor
Afgedankte Elektrische en Elektronische Appa-
ratuur en de implementatie ervan in nationaal
recht moet niet langer te gebruiken elektrisch
gereedschap gescheiden worden verzameld en
op een milieuvriendelijke wijze worden verwerkt.
Wijzigingen voorbehouden; specicaties kunnen
zonder opgave van redenen worden gewijzigd.
Om de machine uit te schakelen, laat u de
aan/uit-schakelaar (1) los.
Om de machine in continubedrijf te schakelen,
houdt u de aan/uit-schakelaar (1) geheel
ingedrukt en drukt dan op de vergrendelknop
(2). Laat vervolgens de aan/uit-schakelaar los.
Om de machine in continubedrijf uit te
schakelen, drukt u de aan/uit-schakelaar (1)
nogmaals in.
Gebruik bij het zagen van metaal altijd
een koelmiddel (bijvoorbeeld
snijvloeistof) om oververhitting van
machine en werkstuk te voorkomen.
Stofafzuiging (fig. F)
De stofafvoeropening zorgt met behulp van een
externe stofzuiger voor stofafzuiging van het
werkoppervlak.
Plaats de adapter (9) op de aansluiting (8).
Sluit een stofzuiger op de machine aan.
Smering (fig. B)
Smeer de geleiderol (11) van tijd tot tijd met
een druppel olie.
REINIGING EN ONDERHOUD
De machine vergt geen speciaal onderhoud.
Reinig regelmatig de ventilatieopeningen.
TECHNISCHE GEGEVENS 56310
Netspanning V 230-240
Netfrequentie Hz 50
Vermogen W 400
Aantal zaagbewegingen
(onbelast) min-
1
3.000
Max. zaagdikte
hout mm 55
kunststof mm 12
staal mm 6
Verstekhoek ° 0-45
Gewicht kg 1,6
GELUID EN VIBRATIE
De A-gewogen geluidsdruk van de machine is
typisch 87,3 dB(A). Onzekerheid K = 3,0 dB(A).
Het geluidsniveau kan tijdens de werkzaamheden
98,3 dB(A) overschrijden.
Draag gehoorbescherming!
Waarde trillingsemissie a = 7,962 m/s
2
Onzekerheid K = 1,5 m/s
2
.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hyundai 56310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hyundai 56310 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info