Manual Hyundai 56212 (page 7 of 15) (English, German, Dutch, French, Polish)

675854

Zoom out

Zoom in

1/15

HYUNDAI

12 13

ENGLISH

TECHNICAL DATA 56212

Mains voltage V 230-240

Mains frequency Hz 50

Power input W 1,200

Speed min

-1

5,800

Min. speed rating saw blade min

-1

5,800

Saw blade diameter mm 185

Max. saw blade thickness mm 1,6

Min. tooth thickness mm 2,4

Blade bore mm 20

Max. depth of cut

90° mm 65

45° mm 46

Mitre angle ° 0-45

Weight kg 3.5

Laser unit

Voltage V 3

Wavelength nm 650

Laser class 2

Protection class III

NOISE AND VIBRATION

Measured values determined according to

EN 60745.1:2009+A11, EN60745-2-5:2010:

Typically the A-weighted sound pressure level of

the machine is 94,72 dB(A). Uncertainty K = 3,0

dB(A).

The noise level when working can exceed

105,72 dB(A).

Wear hearing protection!

Vibration total values (triax vector sum) deter-

mined according to EN 60745.1:2009+A11,

EN60745-2-5:2010: Vibration emission value a

4,746 m/s

. Uncertainty K = 1,5 m/s

GUARANTEE

Refer to the enclosed guarantee conditions for the

terms and conditions of guarantee.

5. Shoe

6. Laser on/off switch

7. Laser

8. Adjusting screw mitre angle

9. Scale for mitre angle

10. Adjusting screw depth of cut

11. Scale for depth of cut

12. Spindle lock button

13. Locking screw

14. Flange

15. Saw blade guard

16. Lever of saw blade guard

17. Parallel guide

18. Adjusting screw parallel guide

19. Battery compartment

The package contains the following parts:

Circular saw

Saw blade

Parallel guide

Spanner

Instruction manual

Safety warnings

Guarantee and service

Replacing the saw blade (g. B)

Only use sharp and undamaged saw blades.

Cracked or bent saw blades must be replaced

immediately.

Before replacing the saw blade always

unplug the tool. Do not use saw blades

made of HSS steel. Make sure that the

spindle diameter Corresponds to the

bore diameter.

Sharp saw blades produce the best

result. Replace worn saw blades on

time by new ones. Remember that

continuous use of worn saw blades

reduces the accuracy of the machine

and may lead to overloading the motor.

• Push the spindle lock button (12) in the

direction of the motor and unscrew the locking

screw (13) counterclockwise.

• Remove the flange (14).

• Raise the saw blade guard (15) with the lever

(16) and remove the saw blade.

• Clean the flange and place the saw blade on

the shaft.

Make sure the teeth and the arrow on

the saw blade point in the same

direction as the arrow on the saw blade

guard (15).

• Reinstall the flange (14) and tighten the

locking screw (13).

• Make sure that the saw blade runs freely by

turning the blade by hand.

Adjusting the depth of cut (g. C)

The depth of cut is innitely adjustable. A clean

cut is achieved with the saw blade protruding from

the material by approx. 3 mm.

• Loosen the adjusting screw (10).

• Set the required depth of cut according to the

scale (11).

• Tighten the adjusting screw.

Adjusting the mitre angle (g. D)

The mitre angle is innitely variable between

0° and 45°.

• Loosen the adjusting screws (8).

• Set the required mitre angle using the scale (9).

• Tighten the adjusting screws.

Mounting the parallel guide (g. E)

The parallel guide allows sawing parallel to an

edge at a maximum distance of 10 cm.

• Loosen the adjusting screw (18).

• Insert the parallel guide (19) into the saw base

(5) as shown in the illustration.

• Set the parallel guide to the required distance.

• Tighten the adjusting screw.

Instructions for use

• Clamp the workpiece. Make sure that the side

which will be visible later is facing down,

because the cut is most accurate at that side.

• Switch on the machine before it touches the

workpiece. Do not exert pressure on the saw

blade. Allow the machine enough time to cut

the workpiece.

• Hold the machine with both hands using both

grips. This ensures optimum control over the

machine.

Switching on and off (g. F)

• To switch the tool on, keep the lock-off button

(2) depressed and press the on/off switch (1).

• To switch the tool off, release the on/off

switch (1).

Using the laser (g. G)

The laser beam is used for projection of the cut on

the workpiece.

• Switch the laser (7) on by means of the on/off

switch (6).

• Place the machine on the workpiece with the

saw marking above the start of the cutting line.

• Check that the laser line aligns with the cutting

line as marked on the workpiece.

• Switch on the machine.

• Follow the “Instructions for use” to perform a

cut.

• After use, switch off the laser.

Dust extraction (g. A1)

The dust extraction outlet together with an

external vacuum cleaner takes care of the dust

extraction of the working surface.

• If necessary, connect an adapter to the

connection (4).

• Connect a vacuum cleaner to the machine.

Lubrication

• From time to time, apply a drop of oil to the

thread of the locking screw (15).

CLEANING AND MAINTENANCE

The machine does not require any special main-

tenance.

• Regularly clean the ventilation slots.

• If necessary clean the laser lens using a

cotton bud soaked in alcohol. Do not use any

other cleansing agents.

Replacing the batteries (g. H)

Suitable batteries are of size AAA.

• Remove the cover from the battery

compartment (19).

• Remove the old batteries.

• Place the new batteries as indicated.

• Replace the cover.

Always replace the complete set of

batteries. Do not mix old batteries with

new ones.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hyundai 56212 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 0,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hyundai 56212 Manual

Product: