675850

Hyundai 56020 Manual

4
Zoom out
Zoom in
Previous page
1/9
Next page
HYUNDAI
6 7
ENGLISH
NOISE AND VIBRATION
Typically the A-weighted sound pressure level of
the machine is 91.4 dB(A). Uncertainty K = 3.0
dB(A).
The noise level when working can exceed 102.4
dB(A).
Wear hearing protection!
Vibration emission value a
h,D
= 15.05 m/s
2
Uncertainty K = 1.5 m/s
2
.
GUARANTEE
Refer to the enclosed guarantee conditions for the
terms and conditions of guarantee.
ENVIRONMENT
Disposal
Your product, accessories and packaging should
be sorted for environmental-friendly recycling.
Do not dispose of power tools into domestic
waste. According to the European Guideline
2002/96/EC for Waste Electrical and Electronic
Equipment and its implementation into national
right, power tools that are no longer usable must
be collected separately and disposed of in an
environmentally friendly way.
Subject to change; specifications can be changed
without further notice.
Changing the direction of rotation (fig. A)
• Press the forward/reverse switch (4) to the left
to drill or to fasten screws.
• Press the forward/reverse switch (4) to the
right to loosen screws.
• Set the forward/reverse switch (4) to the
middle position to lock the machine.
Always wait until the motor has come
to a complete standstill before
changing the direction of rotation.
Adjusting the speed (fig. A)
This machine has been tted with an adjusting
wheel (2) for the maximum speed.
• Turn the adjusting wheel (2) as indicated on
switch (1) to set the maximum speed.
Switching on and off (fig. A)
• To switch the machine on, press the on/off
switch (1). The further you press the switch,
the higher the speed of the machine.
• To switch off the machine, release the on/off
switch (1).
• To switch the machine to continuous mode,
keep the on/off switch (1) pressed and at the
same time press the lock-on button (3).
• Subsequently release the on/off switch.
• To switch off continuous mode, press the on/
off switch (1) again.
CLEANING AND MAINTENANCE
The machine does not require any special main-
tenance.
• Regularly clean the ventilation slots.
TECHNICAL DATA 56020
Mains voltage V 230-240
Mains frequency Hz 50
Power input W 710
No load speed min
-1
0-2,900
Impact (no load min
-1
0-48,000
Drilling capacity in
steel mm 13
wood mm 25
concrete mm 13
Chuck mm 13
Weight kg 1.77
Depth stop
Chuck key
Instruction manual
Safety warnings
Guarantee and service
Inserting and removing a drill or screw bit (fig.
A)
• Open the chuck (7).
• Insert the drill or the screw bit in the chuck.
• Tighten the chuck by hand.
• Tighten the chuck firmly by inserting the chuck
key in one of the holes in the side of the chuck
and turning it clockwise.
• In order to remove a drill or screw bit, proceed
in reverse order.
Before inserting or removing a drill or
screw bit always remove the plug from
the outlet.
Mounting the side handle (fig. A)
• Loosen the knob on the side handle.
• Slide the side handle (6) over the chuck on the
machine.
• Turn the side handle in the required position
and tighten the knob firmly.
Mounting the depth stop (fig. A)
The depth stop is used to limit the maximum
drilling depth.
• Loosen the knob on the side grip.
• Insert the depth stop (8) in its intended hole in
the side grip.
• Set the depth stop to the required drilling
depth.
• Tighten knob firmly.
Selecting the operating mode (fig. A)
Select the required operating mode before use
(drilling or hammer drilling).
• For drilling in wood, metal, plastics and soft
stone and for driving screws slide the switch
(5) to the left.
• For drilling in concrete or hard stone slide the
switch (5) to the right.
Always wait until the motor has come
to a complete standstill before
changing the operating mode.
ELECTRONIC HAMMER
DRILL
56020
WARNING
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result in
electric shock, re and/or serious
injury. Save all warnings and
instructions for future reference.
SAFETY WARNINGS
When using the machine, always observe the
enclosed safety warnings as well as the additional
safety warnings.
The following symbols are used throughout this
manual:
Denotes risk of personal injury or
damage to the machine.
ADDITIONAL SAFETY WARNINGS FOR
ELECTRONIC HAMMER DRILLS
Personal safety
• Do not work materials containing asbestos.
Asbestos is considered carcinogenic.
ELECTRICAL SAFETY
Always check that the power supply
corresponds to the voltage on the
rating plate.
DESCRIPTION (fig. A)
Your electronic hammer drill has been designed
for drilling in wood, metal, plastic, stone and
concrete and it also has been designed for screw
driving applications.
1. On/off-switch
2. Speed adjusting wheel
3. Lock button
4. Forward/reverse switch
5. Switch hammer drill function
6. Side handle
7. Chuck
8. Depth stop
The package contains the following parts:
Electronic hammer drill
Side handle
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hyundai 56020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hyundai 56020 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info