Manual Hwam I45 (page 50 of 60) (English, German, Danish, Swedish, Norwegian)

571929

Zoom out

Zoom in

1/60

It is possible to connect several devices to the same chimney. However, it is important to ﬁrst check the

applicable rules. Contact your local chimney sweeper for the approval of your chimney.

Even a good chimney can function badly if it is not used correctly. Similarly, a bad chimney may function

well if it is used correctly.

Chimney sweeping

To prevent the risk of chimney ﬁres, the chimney must be cleaned every year. The ﬂue duct and the smoke

chamber above the bafﬂe plate must be cleaned together with the chimney. If the chimney’s height makes

cleaning from above impossible, a cleaning hatch must be installed in the chimney.

In case of a chimney ﬁre, close all dampers and call the ﬁreﬁghters. Before any further use, have the

chimney checked by the chimney sweeper.

Test results from nominal test EN 13229:

Nominal heating effect 4.5 kW

Smoke temperature 250°C

Exhaust gas ﬂow 5.9 g/sec.

MountIng and connectIon (draWIng a)

The HWAM I 30/45 consists of a moveable, external brickwork casing, as well as an insert that is pushed

into place and connected once the brickwork casing has been assembled.

The HWAM I 30/45 can be connected in two ways:

1. Mounting and connecting in an existing ﬁreplace.

2. New construction around the insert, possibly including heat ducts to other rooms.

1. Mounting and connecting in an existing ﬁreplace (Drawing A1-A3)

Before mounting the insert in a brick-built ﬁreplace, the regulating damper in the existing chimney must

be removed and the smoke neck, if any, should be widened so that the ﬁre tube from the insert can be

connected directly to the chimney. Any bricks positioned on edge at the bottom of the ﬁreplace should

also be removed.

In advance, decide with a specialist or the chimney sweep where a soot door

(1) should be placed, so

that the ﬁre tube can be cleaned from above while the door of the insert remains closed.

Mounting the smoke pipe (Drawing A1)

First mount the joining ﬂange (2) with a suitable length of ﬁre tubing or ﬂexible tubing (3). Push the

inner pipe into the connector. The inner pipe must be turned so that the handle goes as far as possible

into the connector.

Trim approximately 3 ﬁreproof batts of 50 mm each

(4) so that they ﬁt tightly into the chimney space

and cut a hole in the centre to ﬁt tightly around the tube.

Place the ﬁre tube in the chimney so that the joining ﬂange corresponds to the given measurements.

a. Distance from front edge of the brick hole, if the insert must be ﬂush with the brickwork.

b. Height over the bottom of the insert.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hwam I45 in the language / languages: English, German, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 1,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hwam I45 Manual

Product: