Manual Hwam I30-65 (page 50 of 60) (English, German, Danish, Swedish, Norwegian)

571940

Zoom out

Zoom in

1/60

InstallatIon Manual

Legislation

If the insert is to be mounted in a newly built, non-approved open ﬁreplace, all legal requirements and

local building regulations must be observed. It would always be advantageous to consult your chimney

sweep before mounting the insert.

Room requirements

There must be a constant supply of fresh air to the room in which the insert is to be installed. A window

that opens or an adjustable air vent should sufﬁce.

Please be aware that not all glass parts are heat-resistant. For this reason, a glass wall should sometimes

be treated as a ﬂammable wall, in which case we ask you to contact your local chimney sweep or glass

producer to hear at what distance the insert should be kept from glass.

Distance to inﬂammable materials

Please refer to local building regulations to determine the size of the ﬁreproof area in front of the

ﬁreplace.

The insert must be positioned at least 30 cm above the ﬂoor if the ﬂoor is made of ﬂammable material.

If inﬂammable material is located near the brickwork casing, there must be a minimum of 40 mm of non-

ﬂammable insulation (ﬁre batt) between the casing and inﬂammable material. This applies to all of the

casing’s surfaces. The thermal conductivity of the insulation must be less than 0.09 W/m x K (as measured

at 200 ºC); i.e., thermal conductivity must be lower than 0.09 W/m x K.

Chimney requirements

The chimney must be of a sufﬁcient height to enable an adequate draft and to prevent smoke problems.

Nominal draft: approx. 12 Pa.

The chimney must have a minimum opening equivalent to Ø 150 mm.

The chimney opening should always be at least the size of the outlet socket of the insert.

The chimney must have an easily accessible soot door.

Chimney

The chimney is the “motor” of the insert and it is crucial for the functioning of the woodburning insert.

The chimney draft provides a partial vacuum in the insert. This vacuum removes the smoke from the

insert, sucks air through the dampers for the so-called glass pane rinse which keeps the glass free of soot,

and sucks in air through both primary and secondary dampers for the combustion.

The chimney draft is created by the differences in temperature inside and outside the chimney. The

higher the temperature within the chimney, the better the draft. It is crucial, therefore, that the chimney

is warmed through properly before closing the damper and limiting the combustion in the insert (a brick

chimney takes longer to warm through than a steel chimney).

On days where the weather and wind conditions create insufﬁcient draught inside the chimney, it is even

more important to warm up the chimney as quickly as possible. The trick is to quickly get some ﬂames

going. Split the wood into extra ﬁne pieces, use an extra ﬁrelighter, etc.

If the stove has not been used for a longer period, it is important to check that the chimney pipe is not

blocked.

englIsh

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hwam I30-65 in the language / languages: English, German, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 1,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hwam I30-65

Hwam I30-65 User Manual - Dutch, French, Italian, Spanish - 44 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hwam I30-65 Manual

Product: