613747
10
Zoom out
Zoom in
Previous page
1/52
Next page
10
• Thesmokeshelf(5).Tobeplacedontopofthesteelrailandontheholdersinthesides.
• Two-piecesmokedefectorplate(6).Eachhalfishungonthehookslocatedbeneaththetopplate.Thetwo
halves join in the holders behind the air pipe. Once the stove has been installed, twist the protection off
the two hooks by using pliers or a screwdriver.
• Removablerearplate(2).Thismustalwaysbemountedifthestoveisplacednexttoacombustiblewall.
• Looseheatshield(8)undertheashpan.Thiscanbeusedasalidwhentheashpanisremovedfor
emptying.
Connecting and preparing the HWAM Autopilot IHS
TM
1. Connect the plug
a) to a normal 230V socket
b) to the Air box in the wood section underneath the combustion chamber (lead the plug through
the air slot at the bottom between the side and rear plates - on the left side of the wood-burning
stove when seen from the front. There is a mark on the Air box where the plug should be let in.
See the photo of the power supply on the Air box.
Air box without power supply. Air box with power supply.
2. Insert three AA batteries in the remote control. When the IHS logo disappears from the display, the
remote control is ready to use.
3. The remote control and the wood-burning stove must be connected (the factory will see to this).
If the status line at the bottom of the display is clear (empty) (
) and divided
into three sections, the wood-burning stove and the remote control are connected.
If the status line is dotted ( ), the remote control and the wood-burning stove
are not connected. Start with a display in which the light is off, and make the connection by pressing
and holding down the button, so the advanced menu is displayed. Then press the button repeatedly in
shortintervalsuntilthetext”Linktostove”ishighlightedandwaituntilitentersthismenu.Pressthe
button in short intervals until the text “Connect” is highlighted and wait again. When the text "Please
cycle stove power" appears on the display, disconnect the electricity from the Air box and then recon-
nect. Press the button once more. If the message "Connected to stove" shows up in the display, the
wood-burning stove and the remote control are connected. Press the button once to return to the
main menu. If you do not press the button again, the remote control automatically leaves the menu
and returns to the start display.
4. Go through the self-test of the HWAM Autopilot IHS
TM
:
The self-test of the electronic control is carried out before lighting the first fire in the stove (the
factory will see to this). The self-test can only be done when the wood-burning stove is cold and in
standby mode (no signal in the status line
). Make sure that the display is
not active, i.e. there should be no light in the display (
). If there is light in the
display before you hold down the button for a while, you will instead prepare the wood-burning stove
for lighting (the matchbox will appear in the display) and no self-test can be carried out.
Press the remote control button for approx. 5 seconds in order to enter the menu. Press the button
until the cursor reaches “Self-test”. Wait a few seconds till the remote control enters the “Self-test”
menu. Press the button till the cursor reaches “Engage”. A few seconds later the self-test begins.
By going through a self-test you ensure that all basic operations function correctly.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hwam 7180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hwam 7180 in the language / languages: English as an attachment in your email.

The manual is 6,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hwam 7180

Hwam 7180 User Manual - German - 56 pages

Hwam 7180 User Manual - German - 40 pages

Hwam 7180 User Manual - Dutch, French, Italian - 56 pages

Hwam 7180 User Manual - Italian - 40 pages

Hwam 7180 User Manual - Spanish - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info