613742
39
Zoom out
Zoom in
Previous page
1/48
Next page
39
Min. distances - uninsulated ue gas pipe:
(drawing A)
HWAM 4600
with steel cladding
HWAM 4600
with stone cladding
1. Recommended for brick wall, back, cm
10 10
2.
Recommended for brick wall, side, cm
10 10
1.
For inammable wall, back, cm
20 20
2.
For inammable wall, side, cm
35 45
1.
To inammable wall, corner installation, cm
12 15
3.
Distance to furnishings in front, cm
130 140
Min. distances - insulated ue gas pipe:
(drawing A)
HWAM 4600
with steel cladding
HWAM 4600
with stone cladding
1. Recommended for brick wall, back, cm
7* 7*
2.
Recommended for brick wall, side, cm
7* 7*
1.
For inammable wall, back, cm
7* 7*
2.
For inammable wall, side, cm
40 45
1.
To inammable wall, corner installation, cm
12 15
3.
Distance to furnishings in front, cm
130 140
*We recommend 10 cm to facilitate service on HWAM Autopilot.
Please be aware that not all glass parts are heat-resistant. For this reason, a glass wall should sometimes
be treated as a ammable wall, in which case we ask you to contact your local chimney sweep or glass
producer to hear at what distance the stove should be kept from glass.
Take note of the applicable regulations for the distance between the wall and ue pipe.
The distance to a brick wall is set to faciliate the servicing of the Autopilots system.
Requirements for chimney and smoke pipe
The chimney must be of a sufcient height to enable an adequate draft and to prevent smoke problems. The
stove requires a draft of at least 12 Pa.
The chimney must have a minimum opening equivalent to Ø 15 cm. The chimney opening should always
be at least the size of the outlet socket of the stove. The chimney must have an easily accessible soot door.
Smoke pipe and chimney must always be suitable for a stove connection. Ask your HWAM dealer for more
information.
Changing the ue outlet from a top outlet to a rear outlet (drawing H)
Steps 1 and 12 only apply to the HWAM 4660 and HWAM 4680 models.
1. Remove the heat storage area front (1) by lifting the front and pulling away from the stove.
2. Lift the top plate (2) off the stove.
3. Remove the rear plate (3) by loosening the two screws (4). The rear plate has a cut-out for the ue
pipe. Cut out the plate (5) within this cut-out.
4. The heat shield has a cut-out for the ue pipe. Cut out the plate (6) within this cut-out.
5. Remove the cover plate (7) on the rear of the stove (behind the cut-out plate in the heat shield) by
removing the three screws (8).
6. Remove the smoke ring (9) above the combustion chamber by removing the three screws (10).
7. Place the smoke ring (9) in front of the ue outlet hole on the rear of the stove and afx using the
three screws (10).
8. Place the cover plate (7) so that it closes the ue outlet on top of the combustion chamber (where
the smoke ring was just removed) and afx using the three screws (8).
9. Place the rear plate (3) on the guide taps (11) on the rear side of the stove's base plate and afx the
rear plate using the two top screws (4).
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hwam 4640 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hwam 4640 in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hwam 4640

Hwam 4640 User Manual - Dutch, French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info