744531
14
Zoom out
Zoom in
Previous page
1/20
Next page
Page 14 of 20 pages
Storage of wood
A moisture content of 12-18% is achieved by storing recently felled wood outdoors under a lean-to
for at least one year, preferably 2 years. Wood stored indoors has a tendency to become too dry and
combust too quickly. However, it might be advantageous to store fuel for lighting a fire indoors for a few
days prior to use.
We recommend that you buy a moisture meter to continuously check that the wood has the correct
moisture content before it is used for firing. Split the wood and measure the moisture content of the
split surfaces.
Recommended dimensions
The dimensions of the fuel are important to good combustion. The dimensions should be as follows:
Fuel type Length in cm Diameter in cm
Wood for kindling a fire (finely chopped) 25 2-5
Chopped wood 25 5-8
Special fire lighting guide for stoves with soapstone or natural stone cladding
Stones are natural products which need to adjust to temperature changes. We recommend following
the procedure below:
1. First stoking (drawing F)
Push the air control lever (1) all the way to the right push the shaking grate lever (2) all the way in. Place
2 pieces of wood (5-8 cm in diameter) horizontally in the bottom of the combustion compartment (cor
-
responding to 1-2 kg). Place 5-8 pieces of kindling randomly on top. Place 2 firelighters between the top
layer of kindling. Light up the firelighters and close the stove door. If condensation forms on the glass,
keep the door ajar for a little while and close again. When the fire has gone out, open the door and leave
it open while the stove cools to room temperature.
2. Second stoking
Push the air control lever (1) all the way to the right push the shaking grate lever (2) all the way in. Place
2 pieces of wood (5-8 cm in diameter) horizontally in the bottom of the combustion compartment (cor
-
responding to 1-2 kg). Place 5-8 pieces of kindling randomly on top. Place 2 firelighters between the top
layer of kindling. Light up the firelighters and close the stove door. If condensation forms on the glass,
keep the door ajar for a little while and close again.
When no more yellow flames are visible and a suitable layer of embers has built up, the stove can be
stoked again. There is a suitable layer of embers when the bottom of the stove is covered completely.
Half fill the combustion chamber with dry wood with a diameter of about 7-9 cm. When all of the wood
has caught fire, turn the regulator (1) to middle position. Allow the fire to burn and let the stove cool to
room temperature before stoking again.
3. Third stoking
Repeat the procedure for the second stoking, Allow the fire to burn and let the stove cool to room
temperature after the fire has gone out.
Restoking:
Follow the general instructions, see the sections “Lighting the stove” and “Stoking”.
Lighting the stove (drawing F)
A successful combustion process requires that the wood is lit in the right way. A cold stove and a cold
chimney challenge the combustion process. It is important to achieve a high flue gas temperature quickly.
Push the air control lever (1) all the way to the right push the shaking grate lever (2) all the way in. Place
2 pieces of wood (5-8 cm in diameter) horizontally in the bottom of the combustion compartment
(corresponding to 1-2 kg). Place 5-8 pieces of kindling randomly on top. Place 2 firelighters between the
top layer of kindling. Light up the fire-lighters and close the stove door. If condensation forms on the
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hwam 4130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hwam 4130 in the language / languages: English as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hwam 4130

Hwam 4130 User Manual - German - 20 pages

Hwam 4130 User Manual - Dutch - 20 pages

Hwam 4130 User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info