Manual Hwam 3120 (page 12 of 20) (English)

571927

Zoom out

Zoom in

1/20

Page 12 of 20 pages

• Smoke ﬂue regulating damper (16).

• Soot door (17).

Fitting the loose parts

Before the stove is installed, you must ensure that all loose parts are ﬁtted correctly. Check that all insula-

tion plates of the combustion chamber have been properly placed, i.e. that the bottom plate is horizontal

and that the side plates are vertical and reach all the way up to the steel sides of the combustion chamber

and down to the bottom plate.

Vertical cross-section of the stoves (Drawing B):

• The top plate of the stove (1).

• Removable rear plate (2). This must always be mounted if the stove is placed next to a combustible

wall.

• Back outlet (3). At the factory this is sealed with a cover plate. The smoke outlet is therefore hidden

behind the plate.

• Top smoke outlet (4).

• The smoke shelf (5). To be placed on top of the steel rail and on the holders in the sides.

• Two-piece smoke defector plate (6). Each half is hung on the hooks located beneath the top plate. The two

halves join in the holders behind the air pipe. Once the stove has been installed, twist the protection off

the two hooks by using pliers or a screwdriver.

• Loose heat shield (7) under the ash pan. This can be used as a lid when the ash pan is removed for emptying.

This must always be mounted when the stove is burning

Chimney

The chimney is the “engine” of the stove and it is crucial for the functioning of the woodburning stove.

The chimney draft provides a partial vacuum in the stove. This vacuum removes the smoke from the stove,

sucks air through the dampers for the so-called glass pane rinse which keeps the glass free of soot, and

sucks in air through both primary and secondary dampers for the combustion.

The chimney draft is created by the differences in temperature inside and outside the chimney. The higher

the temperature within the chimney, the greater the draft. It is crucial, therefore, that the chimney is warmed

up properly before closing the damper and limiting the combustion in the stove (a brick chimney takes

longer to warm up than a steel chimney). On days where the weather and wind conditions create insufﬁcient

draught inside the chimney, it is even more important to warm up the chimney as quickly as possible. The

trick is to quickly get some ﬂames going. Split the wood into extra ﬁne pieces, use an extra ﬁrelighter, etc.

If the stove has not been used for a longer period, it is important to check that the chimney pipe is not

blocked.

It is possible to connect several devices to the same chimney. However, it is important to ﬁrst check the

applicable rules.

Chimney sweeping

To prevent the risk of chimney ﬁres, the chimney must be cleaned every year. The ﬂue duct and the smoke

chamber above the bafﬂe plate must be cleaned together with the chimney. If the chimney is too tall to

be cleaned from above, it must be equipped with a soot door.

In case of a chimney ﬁre, close all dampers and call the ﬁreﬁghters. Before any further use, have the

chimney checked by the chimney sweeper.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hwam 3120 in the language / languages: English as an attachment in your email.

The manual is 1.28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hwam 3120

Hwam 3120 User Manual - German, Dutch, French, Italian, Spanish - 11 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hwam 3120 Manual

Product: