571924

Hwam 2630 Manual

10
Zoom out
Zoom in
Previous page
1/36
Next page
10
in short intervals until the text ”Link to stove” is highlighted and wait until it enters this menu. Press
the button in short intervals until the text “Connect” is highlighted and wait again. When the text
“Please cycle stove power” is displayed, disconnect the power supply and then reconnect. Press the
button once more. If the message "Connected to stove" shows up in the display, the wood-burning
stove and the remote control are connected. Press the button once to return to the main menu. If
you do not press the button again, the remote control automatically leaves the menu and returns to
the start display.
4. Go through the self-test of the HWAM Autopilot IHS
TM
:
The self-test of the electronic control is carried out before lighting the first fire in the stove (the
factory will see to this). The self-test can only be done when the wood-burning stove is cold and in
standby mode (no signal in the status line
). Make sure that the display is
not active, i.e. there should be no light in the display (
). If there is light in the
display before you hold down the button for a while, you will instead prepare the wood-burning stove
for lighting (the matchbox will appear in the display) and no self-test can be carried out.
Press the remote control button for approx. 5 seconds in order to enter the menu. Press the button
until the cursor reaches “Self-test”. Wait a few seconds till the remote control enters the “Self-test”
menu. Press the button till the cursor reaches “Engage”. A few seconds later the self-test begins.
By going through a self-test you ensure that all basic operations function correctly.
A self-test consists of four test types:
• A software test
• A test of the temperature sensor and calibration
• A test of the lambda sensor and calibration
• A test of the three motor valves and calibration
The remote control will respond with the text ”Pass” if everything is OK or ”Failed” if there is a
problem. The remote control will also respond with the text "Failed" if you, prior to self-test with the
remote control, have prepared the wood-burning stove for lighting up a fire (made the match box
appear on the display). If the electric power is cut and switched on again, the programme will return
to standby and the self-test can be carried out. If the remote control responds with the text "Not
completed", the self-test could not be carried out, either because the wood-burning stove has not
cooled off or because it is not in standby mode.
5. The remote control must be placed in the same room as the wood-burning stove and in a location
where it is neither exposed to direct heat radiation from the stove nor to direct sunlight. The reason
is that the remote control functions as a thermometer. The room temperature is transmitted wirelessly
to the stove’s electronic control to support the intelligent regulation of the combustion. The remote
control stand can be mounted on the wall.
Chimney
The chimney is the “engine” of the stove and it is crucial for the functioning of the woodburning stove.
The chimney draft provides a partial vacuum in the stove. The partial vacuum removes the smoke from
the stove, sucks air through the damper to the so-called pane flush mechanism, which keeps the window
pane soot free, and sucks air into the combustion via the HWAM Autopilot IHS
TM
.
The chimney draft is created by the differences in temperature inside and outside the chimney. The higher
the temperature within the chimney, the greater the draft. A brick chimney takes longer to warm up than a
steel chimney. On days where the weather and wind conditions create insufficient draught inside the chimney,
it is even more important to warm up the chimney as quickly as possible. The trick is to quickly get some
flames going. Split the wood into extra fine pieces, use an extra firelighter, etc.
If the stove has not been used for a longer period, it is important to check that the chimney pipe is not blocked.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hwam 2630 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hwam 2630 in the language / languages: English, Italian as an attachment in your email.

The manual is 3,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hwam 2630

Hwam 2630 User Manual - German, Dutch, French - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info