627053
8
Zoom out
Zoom in
Previous page
1/16
Next page
8
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
Druk op knop A om de spindel aan te zetten.
Druk op knop B om de spindel te stoppen.
Druk in geval van nood op noodstop C
D licht op als de machine is ingeschakeld.
Draai schakelaar E naar rechts om de koelpomp aan te zetten, naar links om de koelpomp uit te zetten.
Draai keuzeschakelaar F naar rechts om de spindel linksom te laten draaien; naar links om de spindel rechtsom
te laten draaien.
Nadat de machine volledig is afgesteld voor de gewenste bewerking, kan op startknop A worden gedrukt.
6.2 belangrIJksTe onderdelen
6.2.1 hendels voor InsTellen ToerenTal en voedIng
Het toerental wordt gewijzigd met de twee hendels aan de voorzijde van de kop. Plaats de linker hendel in de
positie L voor laag toerental en H voor hoog toerental en de rechter hendel in positie 1,2 of 3 volgens de tabel
boven de hendels.
Wijzig het toerental alleen als de spindel stilstaat!
6.2.2 Tafel
De tafel is in hoogte verstelbaar, 360
O
draaibaar en 90
O
kantelbaar. Maak de klem van de tafelvergrendeling
(6, afbeelding 3) los om de tafel te draaien en kantelen of in de gewenste hoogte te zetten met de hendel
(12, afbeelding 3).
6.2.3 T-sleuven
Zie onderstaande afbeelding voor de afmetingen van de T-sleuven
Afbeelding 5
6.2.4 Terughaalveer
Ga als volgt te werk om de terughaalveer te spannen:
Maak de afdekking van de spindelveer schoon.
Draai de borgmoer los en trek de afdekking iets naar u toe. Houdt de afdekking hierbij goed vast.
Draai de afdekking linksom om de veerspanning te verhogen, rechtsom om de spanning te verlagen. Draai de
afdekking in de gewenste richting tot de volgende inkeping pakt.
Draai de borgmoer weer aan. Niet te vast aandraaien anders kan de spindel niet vrijelijk bewegen.
6.2.5 beschermkap boorkop
De machine is voorzien van een beschermkap voor de boorkop. Sluit de beschermkap voordat u op de startknop
drukt. De machine zal niet starten wanneer de beschermkap niet gesloten is. Wanneer de beschermkap tijdens de
bewerking wordt geopend, zal de machine uitschakelen.
14. SPECIFICATION OF T-SOLT
The size of T-Solt on table as Fig 8:
Fig 8
15. MAINTAINING
That's easier to keep machine in good condition or best performance by means of maintaining it at any time than
remedy it after it is out of order.
(1) Daily Maintenance (by operator)
(a) Fill the lubricant before starting machine everyday.
(b) If the temperature of spindle caused over-heating or strange noise, stop machine immediately to cheek it for
keeping accurate performance.
(c) Keep work area clean; release vise, cutter, work-piece from table; switch off power source; take chip or dust
away from machine and follow instructions lubrication or coating rust proof oil before leaving.
(2) Weekly Maintenance
(a) Clean and coat the cross leading screw with oil.
(b) Check to see if sliding surface and turning parts lack of lubricant. If the lubricant is insufficant, fill it.
(3) Monthly Maintenance
(a) Adjust the accurate gap of slide both on cross and longitudinal feed.
(b) Lubricate bearing, worm, and worm shaft to avoid wear.
(4) Yearly Maintenance
(a) Adjust table to horizontal position for maintenance of accuracy.
(b) Check electric cord, plugs, switches at least once a year to avoid loosening or wearing.
16. CLEANING & LUBRICATING
CLEANING
(1) Your machine has been coated with a heavy grease to protect it in shipping. This coating should be completely
removed before operating the machine. Commercial degreaser, kerosene or similar
14
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 50 G TOPLINE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 50 G TOPLINE in the language / languages: Dutch as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info