627042

Huvema HU 40 SUPER VARIO Manual

8
Zoom out
Zoom in
Previous page
1/24
Next page
8
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED CHANG E S AND T YPI N G ERRORS RESERVED
7.2 Tapping
These machines have a special unit for tapping, it is a quick change device. During tapping, if you want the spindle
to reverse and to withdraw the tapping tip, just push up the grip handle (as shown in figure 7). If you want to
continue tapping, just press down the grip handle (as shown in figure 8).
Always keep the protective drill head cover closed during operation. It is controlled by a micro switch, ensuring that
the machine is switched off when the cover is opened.
7.3 Work Table aDjUsTmenT
• Loosen the clamp handle on the left hand side (figure 9).
• Turn the table handle until the table has reached its proper position (figure 10).
• Tighten the clamp handle.
7.4 Vise aDjUsTmenT (hU 32 only)
Loosen the work table and vise set screws and turn the work table 180 degree, as shown in figures 11 and 12.
Retighten the set screws.
1. Adjustment of feeding limit
To prevent unwanted penetration to work piece, the feeding limit
shall be set by adjusting the appropriate position of feeding depth
fixing button as long as the distance between the end of tool and
top surface if work piece is measured.
A. Setting of feeding depth
1. Loosen knob A.
2. Turn scaled ring B to desired feeding depth.
3. Lock knob A.
2. Work table and vise adjustment
Loose the work table and vise set screw then turn the work table 180 degree, let the vise be upside.
Then completely tight the set bolt. Figure 13.14.15.16
6.Please open water outlet valve and adjust a proper water outlet volume after power supplying. Fig 17
11
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Loose
Loose
Lock
Wrench Size 19m
Figure 11 Figure 12 Figure 13
shownin Figure 12.) If you want to continue to operate, just press down grip handle.(as
shownin Figure 13.)
3. Protect safety guard shall be allocated in a proper position in operation. It is controlled by a micro
witch.(For CE)
10
4. Adjustment of feeding limit
To prevent unwanted penetration to work piece, the feeding limit
shall be set by adjusting the appropriate position of feeding depth
fixing button as long as the distance between the end of tool and
top surface if work piece is measured.
A. Setting of feeding depthFeed Depth Adjustment
5.Work table and vise adjustment
Loose the work table and vise set screw then turn the work table 180 degree, let the vise be upside.
Then completely tight the set bolt.Figure 14.15.16.17
Figure 12
Figure 13
Lock
Loose
A
Figure 7
Figure 8
6.Please open water outlet valve and adjust a proper water outlet volume after power supplying. Fig 18
11
7.Adjust work table position
(1)Firstly, loose the clamp handle in left hand(Figure 19)
(2)Then swing the table handle to properly position. (Figure 20)
(3)Finally tight the clamp handle.(Figure 19)
8.Pulley Cover Open and Close Method
(1)Open iron cover—hold the handle of left iron cover (Figure 21A) and push upward to the highest point and then release
slightly; use locator (Figure 22 B) to fix the iron cover as open state.
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Loose
Loose
Lock
Figure 19
Figure 20
6.Please open water outlet valve and adjust a proper water outlet volume after power supplying. Fig 18
11
7.Adjust work table position
(1)Firstly, loose the clamp handle in left hand(Figure 19)
(2)Then swing the table handle to properly position. (Figure 20)
(3)Finally tight the clamp handle.(Figure 19)
8.Pulley Cover Open and Close Method
(1)Open iron cover—hold the handle of left iron cover (Figure 21A) and push upward to the highest point and then release
slightly; use locator (Figure 22 B) to fix the iron cover as open state.
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Loose
Loose
Lock
Figure 19
Figure 20
Figure 9 Figure 10
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 40 SUPER VARIO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 40 SUPER VARIO in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 40 SUPER VARIO

Huvema HU 40 SUPER VARIO User Manual - German - 24 pages

Huvema HU 40 SUPER VARIO User Manual - Dutch - 24 pages

Huvema HU 40 SUPER VARIO User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info