627042
6
Zoom out
Zoom in
Previous page
1/24
Next page
6
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
5. Bedieningspaneel
6. afstellen Van de tafel
Hoogte verstelling
Om de tafel verticaal te verstellen, de klembout losdraaien, de tafel in de juiste positie brengen door aan de hendel
te draaien en de klembout weer stevig vastzetten.
360° draaibaar
Draai de klembout los en draai de tafel naar de gewenste positie, zet de klembout vast.
6.1 Klem geBrUiKen (hU 32 sUper Vario)
Maak de tafel los en keer de tafel om zodat de klem aan de bovenkant komt. Vergrendel de klem met de klembout.
JS-834V or JS-840VB
A.min-1 or /min (R.P.M.) Indicator
B. Speed Control Switch
C. Fault light
D.Start Button
E. Emergency Stop Button(For CE)
F.Feed Depth Adjustment
G. Drill / Tap Switch
H. Stop Button
I. Cutting Liquid Control Switch
1. Check the power source
Push the start button to judge the motor and spindle shaft is in normal condition or not.
2. Spindle speed adjustment is controlled by the speed control switch. The speed will be
showed out in the electronic digital meter.
3. If it needs to stop urgently, just push the emergency stop switch.
4. Drill / Tap switch: For changing the machine to Drill Mode or Tap Mode.
9
3-2. Operation illustration and procedure:
1. There are three T grooves in the worktable. It is used to fix the work piece.
1-1.There are two T grooves in the base, too. It is convenient for fixing the longer, heavier and larger
working piece.
(Option)
2. These machines have special design for tapping, a quick change device. During tapping, if you
want spindle to turn reversely and withdraw tapping tip, just pull up grip handle only(as
JS-834V
A: Weergave snelheid
B: Knop voor instellen snelheid
C: Waarschuwingslicht
D: Startknop
E: Noodstop
F: Diepte-instelling
G: Keuzeknop boren - tappen
H: Stopknop
I: Keuzeschakelaar koelmiddel aan/uit
Afbeelding 4
1. Adjustment of feeding limit
To prevent unwanted penetration to work piece, the feeding limit
shall be set by adjusting the appropriate position of feeding depth
fixing button as long as the distance between the end of tool and
top surface if work piece is measured.
A. Setting of feeding depth
1. Loosen knob A.
2. Turn scaled ring B to desired feeding depth.
3. Lock knob A.
2. Work table and vise adjustment
Loose the work table and vise set screw then turn the work table 180 degree, let the vise be upside.
Then completely tight the set bolt. Figure 13.14.15.16
6.Please open water outlet valve and adjust a proper water outlet volume after power supplying. Fig 17
11
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Loose
Loose
Lock
Wrench Size 19m
Afbeelding 5 Afbeelding 6 Afbeelding 7
Losmaken
Vergren-
delen
Sleutel 19
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 40 SUPER VARIO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 40 SUPER VARIO in the language / languages: Dutch as an attachment in your email.

The manual is 4,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 40 SUPER VARIO

Huvema HU 40 SUPER VARIO User Manual - English - 24 pages

Huvema HU 40 SUPER VARIO User Manual - German - 24 pages

Huvema HU 40 SUPER VARIO User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info