627048
11
Zoom out
Zoom in
Previous page
1/32
Next page
11
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED
Drilling Machine Instruction Book
9
Magnetic feed drilling machine operating manual (Fig14.Fig15)
1 Turning the power switch A on the side of electric box, the power indicator C lights up and the
machine is ready to start.
2 Spanning the work lamp select switch D, the machine work lamp is turned on or off.
3 Spanning
the cooling pump select switch F, the cooling pump is started or stopped.
4 The machine protective cover B is used to insure the operator safety. Closing the protective cover,
the machine is in working condition and opening it, the machine is stopped.
5 According to the depth of borehole, unlock the hand shank N to set staff gauge position and then
tighten it up.
6 Drilling or tapping function select switch G.
6.1 When the select switch G is in the “ ” position, the machine is ready to drill.
6.1.1 For drilling a hole: Spanning the hand shank M, drill head may be fed manually.
6.1.2 For drilling a hole: Pushing the button L which is on the head is fed automatically. Repressing the
button L , the magnetic clutch will release and the drill head must be fed manually.
6.1.3 Automatic feed: When the staff gauge E contacts the down micro switch the magnetic clutch
releases automatically.(Automatic feed is stopped)
6.2 When the select switch G is in “ “ position, the machine is in tapping condition.
6.2.1 Tapping: Pushing the hand shank button L, the machine main shaft may rotate in clockwise or
counterclockwise and the head is tapping or holding back.
6.2.2 Tapping: If the staff gauge E contacts the up micro switch, the main shaft can rotate in clockwise
automatically. If the staff gauge E contacts the down micro switch, the machine main shaft can rotate
in counterclockwise. (The head can automatically hold back to insure tapping in safe condition.)
7 Spanning the steering select switch J can set the main shaft rotate direction.
7.1 Drilling a hole: In general, the main shaft rotates in clockwise. If the drill head is in counterclockwise,
the steering select switch J must be spanned in counterclockwise position.
7.2 Tapping: The main shaft rotation should be determined in accordance with the screw tap rotate
direction. If not, after spanning the steering select switch J, you should push the start button L to
determine the main shaft rotation in accordance with screw tap rotate direction.
8 If the main shaft rotate, feed, tapping or drilling is set properly, push the start button K to make the
machine rotate.
9 When the machine is in working condition, spanning the steering select switch J or the select switch G,
it would be stopped. You must repress the start bottom to make the machine rotate again.
10 When the machine is in working condition, if pushing the stop button I, it must be stopped out of
power. Returning the stop button in counterclockwise direction to make it move back, the machine
can be only started again.
11 spanning the high or low speed select switch H can change the main motor speed. When the switch
H is set in “2” position, the main motor speed is high. When the switch H is set in “1” position, the
main motor speed is low.
Fig 2
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 40 G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 40 G in the language / languages: English as an attachment in your email.

The manual is 2,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 40 G

Huvema HU 40 G User Manual - German - 28 pages

Huvema HU 40 G User Manual - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info