627048

Huvema HU 40 G Manual

9
Zoom out
Zoom in
Previous page
1/32
Next page
9
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
6.1.1 keuzeschakelaar g voor boren of tappen
Boren is mogelijk wanneer u schakelaar G naar links draait:
• Bedien het handwiel M om de boorkop naar boven of beneden te bewegen.
• Druk op knop L voor automatische voeding. Druk opnieuw op knop L, de elektromagnetische koppeling
wordt uitgeschakeld en de boorkop kan weer handmatig met het handwiel naar boven en beneden bewogen
worden.
• Wanneer de diepteaflezing E het laagte punt bereikt (de spindel is volledig uitgelopen), dan wordt contact
gemaakt met een microschakelaar die daarop de elektromagnetische koppeling uitschakelt.
Tappen is mogelijk wanneer u schakelaar G naar rechts draait:
• Druk op knop L, de spindel draait naar links of rechts.
• Wanneer de diepteaflezing E het hoogste punt bereikt, dan draait de as automatisch naar rechts, bereikt de
diepteaflezing het laagste punt, dan draait de as naar links.
6.2 belangrIJkste onderdelen
6.2.1 hendels voor Instellen toerental en voedIng
Het toerental van de spindel wordt ingesteld door middel van de hendels.
Met de linkerhendel kiest u een kleur. Afhankelijk van de gekozen kleur wordt
het toerental door middel van de rechterhendel ingesteld. Trek licht aan de
hendels en draai ze voor de juiste instelling. Draai aan de keuzeschakelaar aan
de linkerkant van de kop om de voedingssnelheid in te stellen.
6.2.2 automatIsche gereedschapuItwerper
Ga als volgt te werk om het gereedschap uit de spindel te halen:
1. Laat de spindel een stukje uitlopen en druk op de knop van de
gereedschapuitwerper.
2. Haal de spindel weer omhoog.
3. Hou het gereedschap met de hand vast, terwijl u de spindel omhooghaalt.
Waarschuwing
De knop van de gereedschapuitwerper mag niet ingedrukt blijven.
Drilling Machine Instruction Book
6
SPEED SELECTOR
By means of levers spindle speeds are selected. Left lever
selects a colour. Depending on the color selected, right
lever selects a spindle speed value. For moving these
levers, slightly pull them and the rotate.
FEEDS SELECTOR
To select the feed speed, turn the side selector until the
required point (value).
AUTOMATIC TOOL EJECTOR
To remove the tool from the spindle, perform the following
operations:
1. — Lower the spindle from the reels a little bit and
introduce the extractor bolt .
2.—Raise the spindle from the reels.
3.—Hold the too with the hand when raising the spindle or
it will fall on to the table.
ATTENTION: Do not leave the extractor bolt introduced.
RETURN SPRING
To tauten the return spring in model extract the quill until the
teeth of the working gear can move freely .Then move the
reels in the arrow direction and introduce the quill again.
Unfasten the screws in the plastic cover and turn this
cover in positive direction, once it is tautened, fasten the
screws again.
Fig 10
Fig 11
Fig 12
Drilling Machine Instruction Book
6
SPEED SELECTOR
By means of levers spindle speeds are selected. Left lever
selects a colour. Depending on the color selected, right
lever selects a spindle speed value. For moving these
levers, slightly pull them and the rotate.
FEEDS SELECTOR
To select the feed speed, turn the side selector until the
required point (value).
AUTOMATIC TOOL EJECTOR
To remove the tool from the spindle, perform the following
operations:
1. — Lower the spindle from the reels a little bit and
introduce the extractor bolt .
2.—Raise the spindle from the reels.
3.—Hold the too with the hand when raising the spindle or
it will fall on to the table.
ATTENTION: Do not leave the extractor bolt introduced.
RETURN SPRING
To tauten the return spring in model extract the quill until the
teeth of the working gear can move freely .Then move the
reels in the arrow direction and introduce the quill again.
Unfasten the screws in the plastic cover and turn this
cover in positive direction, once it is tautened, fasten the
screws again.
Fig 10
Fig 11
Fig 12
Afbeelding 10 – instellen toerental en voeding
Afbeelding 11 – automatische gereedschapuitwerper
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 40 G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 40 G in the language / languages: Dutch as an attachment in your email.

The manual is 3,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 40 G

Huvema HU 40 G User Manual - English - 32 pages

Huvema HU 40 G User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info