627033

Huvema HU 32-4 TOPLINE Manual

9
Zoom out
Zoom in
Previous page
1/20
Next page
9
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED
addiTional safeTy rules
Always keep in mind that:
• the machine must be switched off and disconnected from the power supply during maintenance and repairs,
• clamped workpieces may only be measured when the machine is switched off.
Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap.
Do not remove safety devices or guards. Never use the machine while a guard is open.
Always use safety glasses for machining rough materials.
Burrs and chips should only be removed using a sweeper or other aid, never with your bare hands!
Never leave the machine running unattended.
2. insTrucTions for using This machine
Read the safety rules carefully and always observe them. Examine the applications of this machine and beware of
possible risks.
Always wear safety glasses!
1. Caution: This drill press in intended for use only with drill bits. The use of other accessories may be hazardous.
2. Correct drilling speeds: Factors which determine the best speed to use in any drill press operation are the kind of
material being worked on, the size of the hole, the type of drill or other cutter and the quality of the cut desired.
The smaller the drill, the greater the required RPM. In soft materials, the speed should be higher than for hard
materials.
3. Drilling in metal: Use clamps to hold the work when drilling in metal. The work should never be held with bare
hands. The flutes of the drill may seize the work at any time, especially when breaking through the stock. If the
piece is whirled out of the operator's hand, he may be injured. In any case, the drill will break when the work
strikes the column.
4. The work must be clamped firmly while drilling, any tilting, twisting or shifting results not only in a rough hole,
but also increases the risk of the drill breaking. For flat work, lay the piece on a wooden base and clamp it firmly
down against the table to prevent it from turning. If the piece is of irregular shape and cannot be laid flat on the
table, it should be securely blocked and clamped.
5. The chuck must be securely fastened to the spindle so that it can't separate from the spindle.
6. Remove the key from the chuck after adjustment.
7. The tool has to be disconnected from the power supply while the motor is being mounted or connected.
8. Secure the tool to the supporting structure if, during normal operation, there is any tendency for the tool to tip
over, slide or walk on the supporting surface.
9. The set screws of the head frame should be secured tightly before using the machine.
3. unpacking
Unpack the carton and check for the parts below:
Fig. A. Main parts Qty.
1 Head 1
2 Column with flange 1
3 Bracket 1
4 Table 1
5 Base 1
If you find any parts missing or damaged, contact your dealer.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 32-4 TOPLINE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 32-4 TOPLINE in the language / languages: English as an attachment in your email.

The manual is 4,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 32-4 TOPLINE

Huvema HU 32-4 TOPLINE User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info