627045

Huvema HU 25 T Manual

9
Zoom out
Zoom in
Previous page
1/16
Next page
9
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
48 Handle 116 Center shaft
49 Sleeve fasten ring 117 Sleeve
50 Bearing 7206
e
118 Connect sheet
51 Bearing cover 119 Gear z33
52 O shape seal 120 Inner gear sheet
53 Oil cup 121 Connector
54 Taper head fasten screw 122 Key
55 Fixture sleeve 123 Gear z51
56 Key 124 Sleeve
57 Worm gear z28 125 Bearing 3056203
58 Sleeve 126 Gear z42
59 Small shaft 127 Fixture ring
60 Gear z17 128 Taper ring
61 Connection rod 129 Pin
62 Handle base 130 Arm
63 Handle ball 131 Shaft pin
64 Handle bar 132 Tape pin
65 Handle base 133 Handle
66 Pin 134 Spring
67 Elastic block ring 135 Steel ball
68 Washer
6. sTrUcTUre anD aDjUsTmenT
The vertical column is mounted on the bottom base, loosen the fasten handle 63 ( fig.5 ) and rotate handle 17
( fig.2 ), the spindle box can move along the vertical column, loosen the fasten handle 63, the spindle box fixed
at any position, so to suit the different machining requirements, loosen cover nut 73 ( Fig.5 ) and rotate nut 72,
the swivel angle of the fasten handle can be adjusted and the tightness of the spindle box can also be changed,
when adjustment completes, fasten the cover nut.
The gear box is mounted on top of the spindle box, rotate the feed handle 89 ( Fig.5 ) the spindle will move up
and down along with the sleeve Remove the gear box, loosen the anti-motion washer 41 ( Fig.4 ), adjust nut 40,
the clea ance of the spindle bearing can be altered. The above adjustments have been set when put to shipment,
nonqualified personal is not allowed to de this adjustments.
7. Transmission sysTem
The spindle rotate ( Fig. 6 ) through motor and gear 95;126 or 99;100 to shaft . Through gear 102; 123 or 108;119
to shaft. Through guide and transmission key to spindle. The motor has double- speed, through changing the
transmission gears, the spindle will rotate in 8 grades of speeds.
Spindle feed motion. The spindle feed movement is controlled manually, the handle 88 ( Fig.5 ) through gear,
gear rack transmission, to make the spindle sleeve move downwards so realise the feed motion.
The up and down motion of the spindle box. It is also controlled by hand, loosen the fasten handle 63 ( Fig. 5 ),
move handle 17 ( Fig.2 ), the spindle box will move up or down.
8. operaTion
Before start the motor, first rotate the change switch ( 21 ) on the spindle box till teach the required position (
high speed to “2R”, Low speed to “1R”, low speed and reverse direction to “1L” ) , then press down the start switch
“1” (green) ; for stop the machine press “O” button ( red ): for reverse rotation, fist to stop the machine and rotate
the speed change switch to “1L” or “2L” wait till the motor to stop completely and then press the start switch.
The speed selection is realised through handle 133 ( Fig.7 ), adjust handle 133 to realise 4 kinds of speed
variations, matched with double speed motor, we can gain 8 grades of speeds ranging from 100 rpm to 2900 rpm.
It should be noted that the speed variations could only be done when the machine has stopped so to avid any
possible damages to the gears and couplers.
About the drilling depth, you only need to adjust the nut 38 ( Fig.2 ) to the require dimension. The drill automatic
release applies to GB1443-85 (ISO 296-1974 ). Morse 3 outer taper with flat tail, its operation is 1:ke this: put out
the handle 48 ( Fig.4 ), rotate handle 88 ( Fig.5 ), then the sleeve will lead the drill to the highest position, the drill
end touches the enter shaft end so to be pushed out, then push 48 to its original position, install the tool.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 25 T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 25 T in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 25 T

Huvema HU 25 T User Manual - German - 16 pages

Huvema HU 25 T User Manual - Dutch - 16 pages

Huvema HU 25 T User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info