627038
8
Zoom out
Zoom in
Previous page
1/16
Next page
8
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
6.3 v-snaar op de jUiste spanning Brengen
Afbeelding 7
Maak knop B aan beide zijden van de kop los
Duw hendel A naar voren om de snaarspanning te verhogen
Maak knop B aan beide zijden van de kop weer vast.
Afbeelding 8
Voor de juiste snaarspanning: oefen met de hand druk uit op de V-snaar. U moet de snaar maximaal 13 mm kunnen
indrukken.
6.4 spindelveer verstellen
Plaats de stopmoeren in de laagste positie en zet vast met moersleutel om te voorkomen dat de spindel zakt
tijdens het op spanning brengen van de veer.
Maak de schroef los en haal de kap weg (afb. 9).
Maak de afdekking van de spindelveer schoon.
JTD-16series
1. Loosen knob B on both sides of headstock.
2. Push handle A forward as arrow sign to get belt tension.
3.Lock knob B firmly to fix belt tension.
When speed change is required. Loosen lead bolt (parts no. 22-S2) on both side of headstock. Pull belt
handle (parts no. 26) to allow belts repositioning and then move belts to correct groove to acquire
desired speed. See following speed chart for reference.
JTD-16S
JTD-16SA
For proper belt tension, use 10 1bs pressure or hand pressure on the belt as shown as bellow.
Models belt model tables
17
Machine model
Belt specifications
Quantity
JTD-16S
A-42
1
JTD-16SA
A-25 / A-26
2
B
A
5-1. Feed Shaft Spring Tension:
The feed shaft return spring is adjusted at thefactory; however, during the life of the drill pressyou may
want to adjust the feed shaft returnspring so the feed shaft return pressure suits youroperating needs.
To adjust the feed shaft spring tension:
1. UNPLUG THE DRIL PRESS !
2. Wipe off any oil on the spring lock cover so itdoes not slip in your fingers when you hold the
cover from spinning (see Figure 28).
3. While holding the spring lock cover against the side of the head stock so the cover stayssplined with
the locking lug; loosen the jam nut and loosen the cover nut approximately1⁄4" (see Figure 30).
4. Put on heavy leather gloves to protect your hands from possible lacerations if the springuncoils
during the next step.
5. Pull the cover outward just enough to disengage the spring-cover lock slot from thelocking lug. Note:
It is important to keep a good grip during this step. Letting go of thecover will cause the spring to
rapidly uncoil.
6. Rotate the cover counterclockwise to increase spring tension, or let the cover slowly unwind in the
clockwise direction to reduce spring tension.
7. Engage the next available spring-cover lock slot with the locking lug and hold the springlock cover
tightly against the side of the headstock.
8. Snug the cover nut against the spring cover just until the nut stops, and then back offthe nut
approximately 1⁄3 turn, or just enough so there is no binding at complete spindletravel.
9. Hold the cover nut and tighten the jam nut against the cover nut.
21
Figure 27
Figure 29
Figure 30
Figure 28
Lock Nut
Spring Lock
Cover
Spring Cover
Lock Slot
Screw
Wrench
Size 19mm
Afbeelding 9
Afbeelding 10
Afbeelding 11
Afdekking
spindelveer
Inkeping
Borgmoer
Steeksleutel
19 mm
Afbeelding 12
Schroef
JTD-16series
1. Loosen knob B on both sides of headstock.
2. Push handle A forward as arrow sign to get belt tension.
3.Lock knob B firmly to fix belt tension.
When speed change is required. Loosen lead bolt (parts no. 22-S2) on both side of headstock. Pull belt
handle (parts no. 26) to allow belts repositioning and then move belts to correct groove to acquire
desired speed. See following speed chart for reference.
JTD-16S
JTD-16SA
For proper belt tension, use 10 1bs pressure or hand pressure on the belt as shown as bellow.
Models belt model tables
17
Machine model
Belt specifications
Quantity
JTD-16S
A-42
1
JTD-16SA
A-25 / A-26
2
B
A
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 20F SUPER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 20F SUPER in the language / languages: Dutch as an attachment in your email.

The manual is 3,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 20F SUPER

Huvema HU 20F SUPER User Manual - English - 16 pages

Huvema HU 20F SUPER User Manual - German - 16 pages

Huvema HU 20F SUPER User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info