627037

Huvema HU 20 SUPER Manual

7
Zoom out
Zoom in
Previous page
1/16
Next page
7
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED
7. conTrol panel
• Check the power source. Push the start button to check if the motor and spindle shaft are in normal working
condition.
• Spindle speed adjustment is controlled by the speed selection switch.
• In case of an emergency, push the emergency stop.
7.1 T-grooves
• There are T grooves in the worktable and the base. They are used to fix the work piece.
7.2 Work Table aDjUsTmenT
7.2.1 Height adjustment
• Loosen the clamp handle on the left hand side.
• Turn the table handle until the table has reached its proper position.
• Tighten the clamp handle.
7.2.2 Angle adjustment
• Loosen the clamp handle on the left hand side.
• Set the table at the required angle.
• Tighten the clamp handle.
7.2.3 360
O
Turning
• Loosen the clamp handle on the left hand side.
• Turn the table to the desired position.
• Tighten the clamp handle.
3-1.Control panel instruction:
A. Jkm Cam Switch (high/low)
B.Start Button(For CE)
C.Emergency Stop Button (For CE)
1. Check the power source
Push the start button to judge the motor and
spindle shaft is in normal condition or not.
2. If it needs to stop urgently, just push the
emergency stop switch.
14
C
3-1.Control panel instruction:
A. Jkm Cam Switch (high/low)
B.Start Button(For CE)
C.Emergency Stop Button (For CE)
1. Check the power source
Push the start button to judge the motor and
spindle shaft is in normal condition or not.
2. If it needs to stop urgently, just push the
emergency stop switch.
14
C
A: Speed selection switch
B: Start button
C: Emergency stop
Figure 6
3-2.Operation illustration and procedure:
1. There are three T grooves in the worktable. It is used to fix the work piece.
1-1.There are two T grooves in the base, too. It is convenient for fixing the longer, heavier and larger
working piece.
OPTION
2. The pulley cover is strictly prohibited to open in normal operation condition.
3. Protect safety guard shall be allocated in a proper position in operation. It is controlled by a micro
witch. (For CE)
4. Adjustment of feeding limit
To prevent unwanted penetration to work piece, the feeding limit
shall be set by adjusting the appropriate position of feeding depth
fixing button as long as the distance between the end of tool and
top surface if work piece is measured.
A. Setting of feeding depth
1. Loosen knob A.
2. Turn scaled ring B to desired feeding depth.
3. Lock knob A.
15
Lock
Loose
Figure 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 20 SUPER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 20 SUPER in the language / languages: English as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 20 SUPER

Huvema HU 20 SUPER User Manual - German - 16 pages

Huvema HU 20 SUPER User Manual - Dutch - 16 pages

Huvema HU 20 SUPER User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info