Manual Huvema HU 18K-2 TOPLINE (page 11 of 20) (English)

627031

Zoom out

Zoom in

1/20

CHANG E S AND T YPI N G ERRORS RESERVED

5.4 belT Tension adjusTmenT

For proper belt tension: Use a light pressure on the V-belt. The distance should be ± 10%.

5.5 Quill spring adjusTmenT

Figure 16

• Pull the knob towards you and move it to the next or previous notch.

• Check the quill while feeding for smooth and unrestricted movement.

6. usage

6.1 insTalling drills

Insert the drill into chuck jaws about 25.4 mm long. When using a small drill, do not insert it so far that the jaws

touch the flutes of the drill. Make sure that the drill is centered in the chuck before tightening the chuck with the key

(fig. 17).

6.2 posiTioning The worK piece

Always place a piece of wood or plywood on the table. This will prevent "splintering" or making heavy burrs on the

underside of the work piece as the drill breaks through. The wood should make contact with the left side of the

column (fig. 18).

6.3 using The vice

For small work pieces that cannot be clamped to the table, use a drill press vice. The vice must be clamped or bolted

to the table.

7. TroubleshooTing

Problem Possible cause Possible solution

Too much noise Wrong belt tension Adjust tension

Spindle not lubricated Remove spindle quill and lubricate

Pulley loose Tighten pulley

V-belt loose Adjust belt tension

Worn bearing Exchange bearing

Play of the chuck Drill chuck loose Tighten by pressing chuck against

table

Worn spindle shaft or bearing Replace spindle shaft or bearing

Worn drill chuck Replace drill chuck

Motor won't start Power supply Check power cord

Motor connections Check motor connections

Switch connections Check switch connections

Motor windings burned Replace motor windings

Switch broken Replace switch

Drill binds in work piece Excessive pressure on feed handle Apply less pressure

V-belt loose Check belt tension

Drill chuck loose Tighten drill with key

Speed too high Adjust speed

Drill burns or smokes Wrong speed Check speed table

Chips not discharging Clean drill

Dull drill Check sharpness and taper

Needs lubrication Lubricate during drilling

Wrong feed Apply less pressure

Table difficult to raise Needs lubrication Lubricate with a little oil

Bent rack Straighten

Clamp bolt locked Loosen clamp bolt

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 18K-2 TOPLINE in the language / languages: English as an attachment in your email.

The manual is 4,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 18K-2 TOPLINE

Huvema HU 18K-2 TOPLINE User Manual - German - 20 pages

Huvema HU 18K-2 TOPLINE User Manual - Dutch - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Huvema HU 18K-2 TOPLINE Manual

Product: