627035
8
Zoom out
Zoom in
Previous page
1/16
Next page
8
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
Afbeelding 8
Voor de juiste snaarspanning: oefen met de hand druk uit op de V-snaar. U moet de snaar maximaal 13 mm
kunnen indrukken.
6.4 spIndelveer verstellen
Plaats de stopmoeren in de laagste positie en zet vast met moersleutel om te voorkomen dat de spindel zakt
tijdens het op spanning brengen van de veer.
Maak de afdekking van de spindelveer schoon.
Draai de borgmoer los (afb. 10) en trek de afdekking iets naar u toe. Houdt de afdekking hierbij goed vast.
Draai de afdekking linksom om de veerspanning te verhogen, rechtsom om de spanning te verlagen. Draai de
afdekking in de gewenste richting tot de volgende inkeping pakt (afb. 11).
Draai de borgmoer weer aan. Niet te vast aandraaien anders kan de spindel niet vrijelijk bewegen.
Draai de stopmoeren naar de bovenste positie en controleer de spanning tijdens het draaien van de
voedingshendel. Als er niet genoeg spanning op de veer staat, herhaal dan stap 4.
Controleer of de spindel tijdens de aanzet gelijkmatig en ongehinderd beweegt. Als de beweging te stroef
gaat, draai dan de moeren los totdat beweging wel soepel gaat.
7. geBruIK
7.1 Inzetten van Boren
Steek de boor ongeveer 25.4 mm in de boorkop. Bij het gebruik van een kleine boor ervoor zorgen dat de
spanklauwen niet het snijvlak omvatten. Zorg ervoor dat de boor in het midden van de boorkop valt, voordat de
boorkop wordt aangedraaid met de sleutel.
7.2 plaatsIng van het werKstuK
Leg altijd een stuk hout (of multiplex) op de tafel. Dit voorkomt versplinteren of het veroorzaken van erge
bramen aan de onderzijde van het werkstuk als de boor er doorheen breekt. Het hout moet tegen de linkerzijde
van de kolom liggen.
JTD-16series
1. Loosen knob B on both sides of headstock.
2. Push handle A forward as arrow sign to get belt tension.
3.Lock knob B firmly to fix belt tension.
When speed change is required. Loosen lead bolt (parts no. 22-S2) on both side of headstock. Pull belt
handle (parts no. 26) to allow belts repositioning and then move belts to correct groove to acquire
desired speed. See following speed chart for reference.
JTD-16S
JTD-16SA
For proper belt tension, use 10 1bs pressure or hand pressure on the belt as shown as bellow.
Models belt model tables
17
Machine model
Belt specifications
Quantity
JTD-16S
A-42
1
JTD-16SA
A-25 / A-26
2
B
A
5-1. Feed Shaft Spring Tension:
The feed shaft return spring is adjusted at thefactory; however, during the life of the drill pressyou may
want to adjust the feed shaft returnspring so the feed shaft return pressure suits youroperating needs.
To adjust the feed shaft spring tension:
1. UNPLUG THE DRIL PRESS !
2. Wipe off any oil on the spring lock cover so itdoes not slip in your fingers when you hold the
cover from spinning (see Figure 28).
3. While holding the spring lock cover against the side of the head stock so the cover stayssplined with
the locking lug; loosen the jam nut and loosen the cover nut approximately14" (see Figure 30).
4. Put on heavy leather gloves to protect your hands from possible lacerations if the springuncoils
during the next step.
5. Pull the cover outward just enough to disengage the spring-cover lock slot from thelocking lug. Note:
It is important to keep a good grip during this step. Letting go of thecover will cause the spring to
rapidly uncoil.
6. Rotate the cover counterclockwise to increase spring tension, or let the cover slowly unwind in the
clockwise direction to reduce spring tension.
7. Engage the next available spring-cover lock slot with the locking lug and hold the springlock cover
tightly against the side of the headstock.
8. Snug the cover nut against the spring cover just until the nut stops, and then back offthe nut
approximately 13 turn, or just enough so there is no binding at complete spindletravel.
9. Hold the cover nut and tighten the jam nut against the cover nut.
21
Figure 29
Figure 30
Figure 28
Lock Nut
Spring Lock
Cover
Spring Cover
Lock Slot
Wrench
Size 19mm
Afbeelding 9
Afbeelding 10 Afbeelding 11
Afdekking
spindelveer
Inkeping
Borgmoer
Steeksleutel
19 mm
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 16 SUPER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 16 SUPER in the language / languages: Dutch as an attachment in your email.

The manual is 2,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 16 SUPER

Huvema HU 16 SUPER User Manual - English - 16 pages

Huvema HU 16 SUPER User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info