627056
15
Zoom out
Zoom in
Previous page
1/32
Next page
15
Achtung:
Vor Zerlegung der Horizontalwelle müssen Sie die Spindel in ihre oberste Position fahren.sen
Sie dann die Spindelausgleichfeder und unterfüttern Sie die Spindel mit einem Holzblock, falls die
Spindel sich abrupt aus der Halterung löst.
Vor Einbau der Horizontalwellessen Sie die Spindel in ihre oberste Position fahren. Die
Spindelausgleichsnocke muss sich in der spezifizierten Stellung befinden, da sonst die Spindel nicht in
Balance gehalten werden kann.
Kupplung einstellen: Stellen Sie die Kupplung im eingekuppelten Zustand ein. Stellen Sie hierfür mit
Handrad 4 Automatikvorschub ein und ziehen Sie Mutter 3 an, damit die Getriebezähne gut ineinander
eingreifen. Ziehen Sie anschließend Schraube 2 und Mutter 3 der Horizontalspindel 6 an, nachdem Sie sich
von der guten Funktion von Handrad 4 überzeugt haben.
Achtung: Das Ein- und Auskuppeln der Kupplung erfolgt mittels 36 Stahlkugeln. Vermeiden Sie
während der Zerlegung einen Verlust von Stahlkugeln, da unbedingt wieder die gleiche Anzahl
an Stahlkugeln eingesetzt werden muss und diese beim Wiedereinbau nicht durch andere ersetzt
werdenrfen, da sonst die Kupplung beschädigt wird.
5.5 spIndelstockklemmung
spIndelstock-klemmkraft eInstellen
Lösen Sie Schraube 1 und verschieben Sie Komponente 2, womit Sie die Spindelstock-Klemmkraft
einstellen. Stellen Sie die Klemmkraft stark genug ein, bis sich der Spindelstock nicht mehr bei einer auf die
Spindelstock-Handradkante ausgeübten äußeren Kraft von 300 N bewegen lässt.
Verbindungsfläche von Spindelstock und Auslegerarm einstellen:
Lösen Sie Schraube 4 und stellen Sie anschließend mit Exzenterwelle 3 das Spiel zwischen Spindelstock
und Auslegerarm ein. Das mit einer Fühlerlehre ermittelte Tiefenmaß darf bei Bewegung des Spindelstocks
und Ausübung von einer äußeren auf die Handradkante ausgeübten Kraft von bis zu 40 N keine 20 mm
übersteigen.
C H ANG E S A N D T YPI N G E R R O RS R E S E R V E D
C H ANG E S A N D T YPI N G E R R O RS R E S E R V E D
C H ANG E S A N D T YPI N G E R R O RS R E S E R V E D
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema CRDM 3050 X16-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema CRDM 3050 X16-1 in the language / languages: German as an attachment in your email.

The manual is 4,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info