734149

Husqvarna WDC 220 Manual

13
Zoom out
Zoom in
Previous page
1/368
Next page
To install the tube holder
1. Move the tube holder vertically on the extension
tube.
2. Use a screwdriver to install the tube holder on
correct height of the extension tube. (Fig. 19)
3. Park the extension tube at the holders on the rear of
the product. (Fig. 20)
Operation
Introduction
WARNING: Before you operate the product,
you must read and understand the safety
chapter.
To start the product
Before the product is used, make sure that the
frequency and voltage shown on the rating plate is the
same as the mains voltage.
1. Make sure that the main switch is in position "0".
(Fig. 10)
2. Do a check that correct filters are in position in the
product.
3. Put the hose into the vacuum inlet at the front of the
product. Push the hose forward until it is installed
tightly in position in the vacuum inlet. (Fig. 16)
4. Connect the two extension tubes with the handle.
Twist the extension tubes to make sure that they are
correctly in position.
5. Attach a nozzle to the extension tube. Select the
nozzle after the type of material that is to be cleaned.
6. Connect the plug into the mains.
7. Put the main switch into position "I" to start the
product. (Fig. 17)
To stop the product
1. Put the main switch into position "0" to stop the
product.
2. Disconnect the plug from the mains. (Fig. 10)
To use the blow function
1. Put the hose in the opening on the rear of the
product. (Fig. 21)
2. Connect the plug into the mains.
3. Put the main switch to the "I" position. (Fig. 17)
4. Adjust the blow power on the handle or by the main
switch*. *Only on some models. (Fig. 22)
To use the power tool socket*
*Only on some models.
CAUTION:
Follow the operating instructions
and safety instructions for appliances
connected to the power tool socket.
Note: The maximum power consumption of the
connected tool is told in section
Technical data on page
16
.
1. Make sure that the switch on the power tool is in
position "0". (Fig. 23)
2. Disconnect the handle from the hose. Press the
hatches on the hose end (A) and pull out the handle
(B). (Fig. 24)
3. Connect the power tool adaptor. (Fig. 25)
4. Adjust the suction power on the power tool adaptor
or by the main switch*. *Only on some models. (Fig.
26)
5. Connect the hose to the vacuum inlet of the product
and to the power tool. Connect the cable of the
power tool to the electrical connection of the product.
(Fig. 27)
6. Make sure that the switch on the power tool is in
position "0". (Fig. 23)
7. Turn the main switch on the product to the power
tool position (A).
8. Put the switch of the power tool to "I" (B). (Fig. 28)
Note: You can start and stop the product with the
main switch on the product (A) or on the power tool
(B).
To clean liquid
Note: The product has a float system that stops the
airflow through the product at the maximum liquid level.
CAUTION: Do not clean liquid without the
float system in position.
1. Make sure that the filter and the filter tension (the
float system) is in position, see
To replace the filter
on page 15
. Remove the filter bag if it is installed.
2. Use the floor nozzle to clean liquid.
3. At the maximum liquid level, a noticeable change of
the motor sound is heard. The suction power
decreases.
4. Stop the product, see
To stop the product on page
13
.
5. Empty the dirt container, see
To empty the dirt
container after liquid pick up on page 14
.
562 - 004 - 20.03.2019
13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna WDC 220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna WDC 220 in the language / languages: All languages as an attachment in your email.

The manual is 8,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info