477663

Husqvarna TR430 Manual

17
Zoom out
Zoom in
Previous page
1/60
Next page
17
3
5
1. Starter handle
2. Choke lever
3. Spark plug wire
4. Fuel Valve
5. Shift lever indicator
6. Drive control lever "disengaged" po si tion
7. Drive control lever "engaged" position
8. Drive control release "unlocked" po si tion
9. Drive control release "locked" position
10. Throttle control
11. Handle grip
Starting the engine
a. Reconnect spark plug wire (fig. 6).
b. Move shift lever indicator to "N" (neutral) position (fig. 7).
c. Open the fuel valve (fig. 6).
d. Place throttle control (fig. 8) 1/3 of the way towards the
high speed position.
e. Close the choke lever (fig. 6).
f. Grasp starter handle (fig. 6) with one hand and grasp
handle bar with other hand. Pull rope out slowly until
engine reaches start of compression cycle (rope will pull
slightly harder at this point).
g. Pull rope with a rapid, continous, full arm stroke. Keep a
firm grip on the starter handle and let rope rewind slowly.
Do not let starter handle snap back against starter.
h. Repeat steps (e.) and (f.) until engine starts. When engine
starts. Gradually open choke by turning the choke lever
(fig. 6) and then move to fully opened position as engine
warms up.
i. Move throttle control (fig. 8) to the slow position for a few
minutes to warm up engine.
WARNING!
Keep drive control lever in "disengaged" position when start-
ing the engine (fig. 8).
NOTE!
In order to idle smoothly, a new engine may require 3 to 5
minutes running time above slow idle speed. Idle speed has
been adjusted to be correct after this break-in period.
Tine operation
a. Move throttle control to desired speed.
b. To begin tine movement, push down on the drive control
release and squeeze the drive control lever to the "en-
gaged" position (fig. 8).
WARNING!
Always release drive control lever before moving shift lever
into another position. Releasing the drive control lever will
disengage the drive control release.
Figure 6
Figure 7
Figure 8
1
2
4
3
8
9
10
7
6
5
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna TR430 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna TR430 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info