579240
88
Zoom out
Zoom in
Previous page
1/104
Next page
88
6
7
9
9
5
6
4
3
1
2
To Replace Motion Drive Belt
REMOVAL
1. Park tractor on a level surface. En gage parking brake.
CAUTION: Ensure ignition key is removed while work-
ing on tractor.
2. Remove bagger assembly.
3. Remove center discharge chute as previously described.
4. Remove cutting unit as previously described.
5. Disconnect clutch wire harness (1).
6. Remove anti-rotation link (2) on right side of tractor.
7. From the rear of the tractor, work through the backplate and
remove the mower drive belt from the transaxle pulley (3)
and rear idler pulleys (4).
8. Remove belt from middle idler pulleys (5).
9. Work the belt off of the engine pulley (6) and around the
belt guide (7).
INSTALLATION
1. Start the belt from above steering support plate (8) on the
left side of the steering shaft.
NOTE: Ensure the belt is over the top of the clutch/brake pedal
shaft (9).
2. Work the belt onto the engine pulley (6) and under the belt
guide (7).
3. Reinstall anti-rotation link (2) on right side of tractor. Tighten
securely.
4. Reconnect clutch harness (1).
5. Continue installing belt in the reverse order of dismantling.
IMPORTANT: Check belt to ensure proper routing in all mower
pulley grooves and guides.
Antriebsriemen ersetzen
AUSBAU
1. Traktor auf einer ebenen Fläche abstellen. Feststellbremse
anziehen.
WARNUNG: Bei Arbeiten am Traktor muss der Zünd-
schlüssel unbedingt abgezogen sein.
2. Fangkorb abbauen.
3. Mittlere Auswurfschütte wie oben beschrieben abbauen.
4. Schneideinheit wie zuvor beschrieben abbauen.
5. Trennen Sie den Kabelbaum der Kupplung (1).
6. Entfernen Sie die Antirotations-Verbindung (2) an der rechten
Seite des Traktors.
7. An der Rückseite des Traktors beginnend, zur Rückplatte
gehen und den Mäherantriebsriemen von der Getrieberie-
menscheibe (3) und den hinteren Zwischenriemenscheiben
(4) herunternehmen.
8. Riemen von den mittleren Riemenscheiben (5) herunterne-
hmen.
9. Den Riemen von der Motorriemenscheibe (6) und der
Riemenführung (7) herunternehmen.
EINBAU
1. Mit dem Einsetzen des Riemens oberhalb der Lenkträger-
platte (8) auf der linken Seite der Lenkwelle beginnen.
HINWEIS: Der Riemen muss sich dabei über der Oberseite
der Kupplungs-/Bremspedalwelle (9) befinden.
2. Den Riemen auf die Motorriemenscheibe (6) und unter die
Riemenführung (7) setzen.
3. Bauen Sie die Antirotations-Verbindung (2) an der rechten
Seite des Traktors wieder ein. Ziehen Sie die Schrauben
fest an.
4. Schließen Sie den Kabelbaum der Kupplung (1) wieder an.
5. Der Riemen wird weiterhin in umgekehrter Reihenfolge des
Ausbaus eingebaut.
WICHTIG: Die korrekte Verlegung des Riemens in allen Nuten
und Führungen der Mäherriemenscheiben prüfen!
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna TC 342 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna TC 342 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 8,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info