579239

Husqvarna TC 338 Manual

96
Zoom out
Zoom in
Previous page
1/120
Next page
96
6
To Replace Mower Drive Belt
MOWER DRIVE BELT REMOVAL
1. Park tractor on a level surface. En gage parking brake.
2. Lower attachment lift lever to its lowest position.
3. Remove any dirt or grass clippings which may have ac-
cumulated around mandrels and entire upper deck surface.
4. Remove belt from clutch pulley (M), mandrel pulley (R),
and all idler pulleys (V).
MOWER DRIVE BELT INSTALLATION
1. Install belt around both mandrel pulleys (R) and around
idler pulleys (V) as shown.
2. Install belt onto clutch pulley (M).
IMPORTANT: Check belt for proper routing in all mower pul-
ley grooves.
3. Raise attachment lift lever to highest position.
Austauschen des Antriebsriemens des Mähers
ENTFERNEN DES ANTRIEBSRIEMENS DES MÄHERS
1. Parken Sie den Traktor auf einer ebenen Fläche. Legen Sie
die Handbremse ein.
2. Drücken Sie den Hebel für den Anhängerlift auf seine
niedrigste Stellung.
3. Entfernen Sie Schmutz oder Grasreste, die sich vielleicht
rund um die Wellen und auf der ganzen Fläche des Ober-
decks angesammelt haben.
4. Den Riemen von der Kupplungsscheibe (M), der Spindel-
scheibe (R) und allen Umlenkrollen (V) abziehen.
INSTALLIEREN DES ANTRIEBSRIEMENS DES MÄ-
HERS
1. Legen Sie den Riemen rund um die beiden Wellenscheiben
(R) und um die Freilaufscheiben (V) wie abgebildet.
2. Nun legen Sie den Riemen um die Kupplungsscheibe (M).
WICHTIG: Prüfen Sie den richtigen Verlauf des Riemens in
allen Triebradrinnen des Mähers.
3. Heben Sie den Anhängerlifthebel auf seine höchste Stellung.
Pour remplacer la courroie de transmission
DÉMONTAGE DE LA COURROIE DE TRANSMISSION
DE LA TONDEUSE
1. Garez le tracteur bien à plat. Engagez le frein de stationnement.
2. Faites descendre le levier de levage de l’accessoire dans
sa position la plus basse.
3. Eliminez la saleté ou les brins d’herbe qui s’accumulent
autour des arbres et à la surface du pont supérieur.
4. Retirez la courroie de la poulie d’embrayage (M), de la
poulie du mandrin (R) et des poulies guides (V).
MONTAGE DE LA COURROIE DE TRANSMISSION DE
LA TONDEUSE
1. Placez la courroie autour des deux poulies (R) de l’arbre
et des poulies folles (V) de la façon illustrée.
2. Montez la courroie sur la poulie (M) de l’embrayage.
IMPORTANT: Vérifiez si la courroie est correctement passée
dans toutes les gorges des poulies de la tondeuse.
3. Faites monter le levier de levage de l’accessoire dans sa
position la plus élevée.
Sustituir la correa de transmisión cortacésped
QUITAR LA CORREA DE TRANSMISIÓN DEL CORTA-
CÉSPED
1. Aparcar el tractor en una superficie nivelada. Poner el freno
de estacionamiento.
2. Bajar la palanca elevadora hasta su posición más baja.
3. Quitar cualquier suciedad o grasa que puede haberse
acumulado alrededor de los mandriles y toda la superficie
superior de la cubierta.
4. Quite la correa de la polea del embrague (M), la correa del
mandril (R) y las poleas tensoras (V).
INSTALACIÓN DE LA CORREA DE TRANSMISIÓN DEL
CORTACÉSPED
1. Instalar la correa alrededor de las dos poleas del mandril
(R) y alrededor de las poleas-guías (V) como mostrado.
2. Instalar la correa en la polea de embrague (M).
IMPORTANTE: Controlar que la correa gire bien en todas las
ranuras de la polea del cortacésped.
3. Levantar la palanca elevadora hasta la posición más alta.
M
V
R
R
… 96 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna TC 338 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna TC 338 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 14,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info