733949
27
Zoom out
Zoom in
Previous page
1/112
Next page
27
TO INSTALL BAGGER PRESENCE LEVER
WARNING: Shut off tractor engine and engage parking
brake before installing the bagger presence lever.
Position bagger presence lever (1) on backplate with anti-
rotation tab in slot on backplate and align with mounting
hole.
Attach bagger presence lever to the backplate using screw
(3) and nut (2) and tighten firmly.
3
2
1
TO ADJUST BAGGER FULL LEVER/EXTENSION
Slide bagger full extension (4) to the desired position.
For the heaviest/wet grasses, slide extension all the way in.
For the lightest/driest grasses, pull extension all the way out.
TO INSTALL BAGGER FULL LEVER/EXTENSION
Before installation or adjusting, tractor engine must be shut off
and parking brake engaged.
Remove center discharge chute. (See "To Remove Center
Chute" in section 6 of this manual.)
Remove bolt (1) from chassis. Place cover (2) in slots (3)
in backplate. While holding cover in place, place lever (4)
through slot and reinstall bolt (1). Adjust as needed.
1
4
1
2
3
Den Fangkorbgriff (13) durch die Fangkorbabdeckung und
die Bohrungen im Rahmen nach unten schieben.
Den Gabelstift (11) durch die Bohrung am Fuß des
Fangkorbgriffs (13) schieben und die Federklammer (12) in
die Bohrung am Ende des Gabelstifts (11) drücken, bis sie
einrastet.
Querstreben (6) aus dem Fangkorb herausnehmen.
Querstrebe (6) auf den Stift (7) hinten am oberen
Fangkorbrahmen aufschieben und mit Federklammer-
Sicherung (8) fixieren.
Querstrebe (6) auf den Stift (9) vorn am Fangkorbrahmen
aufschieben und mit Federklammer-Sicherung (10) fixieren.
Den Vorgang auf der gegenüberliegenden Seite wiederholen.
Den Gabelstift (11) und die Federklammer (12) vom
Fangkorbgriff (13) abnehmen.
Führen Sie-die Fangkorbeinheit befindet sich auf ihrer
Seite-die vorderen Fangkorbrahmenenden (2) durch
die Stoffschlaufen, die sich jeweils seitlich am Fangkorb
befinden.
Bringen Sie die Karosserieschrauben und die Muttern
(1) wieder so wieder an, dass sie den vorderen und den
oberen Rahmen miteinander verbinden und dabei durch das
Fangkorbmaterial (4) gehen. Die Schrauben fest anziehen.
VORSICHT: Dabei 11,2 Nm nicht überschreiten.
Lassen Sie den unteren Teil des vorderen Fangkorbrahmens
(3) in den Schnappverschluss (5) vorn am Boden des
Fangkorbs einrasten.
MONTIEREN DES FANGKORBS
Den Beutel entfalten und mit der rechten Seite nach oben
aufstellen.
Karosserieschrauben (5/16-18 x 1,5) und Muttern (1) an der
Vorderseite des oberen Rahmens lösen.
1
6
7
9
10
8
1
2
4
53
3
2
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna TC 238T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna TC 238T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 10,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info