579234

Husqvarna ST 261E Manual

15
Zoom out
Zoom in
Previous page
1/76
Next page
15
Install auger control rod
The auger control rod is installed on the snow thrower.
1. Remove plastic tie (A) securing auger control rod (B) to lower handle.
2. Push down on the auger control rod and bring top end of rod up between
the metal console and plastic console cover at right control lever (C).
3. With control lever in the raised position, insert end of control rod in slot
of control lever.
NOTE: Engage lever once and rod should snap into place.
Installation des Steuerhebels für die
einzugsschnecken
Die Steuerstange der Förderschnecke muss am Schneeräumer montiert
werden.
1. Entfernen Sie den Kabelbinder (A), der die Steuerstange der
Förderschnecke (B) am unteren Griff sichert.
2. Drücken Sie die Förderschnecken-Steuerstange nach unten, und bringen
Sie das obere Ende der Steuerstange nach oben zwischen Metallkonsole
und Kunststoffkonsolen-Abdeckung am rechten Steuerhebel.
3. Wenn der Steuerhebel in der angehobenen Position ist, setzen Sie das
Ende der Steuerstange in den Schlitz des Steuerhebels ein (C).
HINWEIS: Betätigen Sie den Hebel einmal, um die Steuerstange einrasten
zu lassen.
Installez la tige de contrôle de la vis sans fin
La tige de contrôle de la vis sans fin est installée sur la souffleuse à neige.
1. Retirez l'attache en plastique (A) maintenant la tige de contrôle de la
vis sans fin (B) pour abaisser la poignée.
2. Abaissez la tige de contrôle de la vis sans fin et placez l'extrémité
supérieure de la tige entre la console métallique et le couvercle de
console en plastique au niveau du levier de commande droit.
3. Avec le levier de commande en position relevée, insérez l'extrémité de
la tige de contrôle dans la fente du levier de commande (C).
REMARQUE: Engagez une fois le levier. La tige doit alors se mettre en position.
Montar la biela de mando de la barrena
La varilla de control de la barrena está instalada en el quitanieves.
1. Retire la sujeción plástica (A) que fija la varilla de control de la transmisión (B) al asa inferior.
2. Empuje hacia abajo la varilla de control de la barrena y sitúe el extremo superior de la varilla entre las tapas de la consola
metálica y de la consola plástica en la palanca de control derecha.
3. Con la palanca de control elevada, introduzca el extremo de la varilla de control en la ranura de la palanca de control (C).
NOTA: Accione la palanca una vez, la varilla debe encajar en su posición.
Het installeren van de regelstang van de boorregeling
De bedieningsstang van de schroeftransporteur is op de sneeuwblazer geïnstalleerd.
1. Verwijder de kunststof strip (A) waarmee de bedieningsstang van de schroeftransporteur (B) bevestigd is aan de onderste
hendel.
2. Duw de bedieningsstang van de schroeftransporteur omlaag en breng het bovenste uiteinde omhoog tussen de metalen
console en het kunststof deksel van de console op de rechter bedieningshendel.
3. Steek, met de bedieningshendel in de geheven stand, het uiteinde van de bedieningsstang in de opening van de
bedieningshendel (C).
OPMERKING: Bedien de hendel één keer, dan zou de stang op zijn plaats moeten klikken.
Montaggio della barra di regolazione della coclea
La barra di regolazione della coclea è installata sullo spazzaneve.
1. Rimuovere la fascetta in plastica (A) che fissa la barra di regolazione della coclea (B) all'impugnatura inferiore.
2. Spingere in basso la barra di regolazione della coclea e portare la sua estremità superiore tra la console metallica e la
copertura in plastica in corrispondenza della leva di comando a destra.
3. Con la leva di comando in posizione sollevata, inserire l'estremità della barra di regolazione nell'apposito alloggiamento
della leva di comando (C).
NOTA: Innestando una volta la leva, la barra dovrebbe scattare in posizione.
A
B
B
C
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna ST 261E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna ST 261E in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info