477703
56
Zoom out
Zoom in
Previous page
1/76
Next page
56
3
2
1
E
D
B
A
H
J
K
M
2
1
F
F
L
To replace belts
The auger and traction drive belts are not adjustable. If the belts are damaged
or begin to slip from wear, they should be replaced. It is recommended that
the belt(s) be replaced by a qualified service center.
NOTE: It is recommended that both the auger and traction drive belt be
replaced at the same time.
The V-belts on your snow thrower are of special construction and should
be replaced by original equipment manufacturer (OEM) belts available from
your nearest dealer. Using other than OEM belts can cause personal injury
or damage to the snow thrower.
WARNING: Belt replacement requires separation of the snow
thrower. While separating the auger housing (1) from the frame as-
sembly (2), it is important that an assistant stand in the op er at ing
position and hold the snow thrower handles (3). Serious personal
injury and/or damage to the unit could occur if the snow thrower
should fall during the belt chang ing process.
1. REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel
tank into a suitable container, outdoors, away from fire or flame. Wipe
up any spilled gasoline.
2. REMOVE DISCHARGE CHUTE - Loosen lock nut securing chute rotator
head to mounting bracket only enough to allow chute rotator head to be
raised and discharge chute to be removed from snow thrower.
3. REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this
section of this manual.
4. REMOVE ENGINE PULLEY (A) - Remove bolt (B), flat washer (D)
securing pulley to engine crankshaft. Remove outside (auger) pulley
(A) only from crankshaft.
5. SEPARATE SNOW THROWER - With your assistant standing in the
operating position holding the handles, re move the four (4) bolts holding
auger housing (1) and frame (2) together.
WARNING: As the last bolt is removed, have your assistant care-
ful ly lower the handles down to the ground.
6. REMOVE AUGER BELT (H) from around pulley (E).
7. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER (J) and remove
traction drive belt (K) from around pulleys.
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in
idler arm (J) and rotate ratchet clockwise to relieve tension.
8. With tension relieved on idler, install new traction drive belt around pul-
leys and inside belt keepers (L).
9. Place auger belt (H) around and inside groove of auger pulley (E) only.
10. While your assistant slowly raises handles to rejoin the auger housing and
frame assembly, pull up on the auger belt and squeeze sides together
above pulley so belt is fully seated in groove of pulley (E).
11. Move idler arm so it does not hit impeller pulley as you bring snow thrower
completely together and check carefully for proper routing of belts. If
auger belt has become dislodged from the pulley (by catching the idler
arm bracket (M) while bringing snow thrower together), separate the
snow thrower and repeat step 12. Belt must be fully seated in pulley
groove when bringing the snow thrower together.
12. Install the four hex bolts (F) and lock washers (G) and tighten securely.
13. INSTALL ENGINE PULLEY (A) - Place belt in pulley groove and slide
pulley on crankshaft. Install flat washer, bolt and tighten securely (30-35
ft. lbs. / 41-47 N-m torque). Make sure belt is inside belt keeper (L).
14. INSTALL BELT COVER and two (2) screws. Tighten securely.
15. INSTALL DISCHARGE CHUTE – See “INSTALL DISCHARGE CHUTE
/ CHUTE ROTATER HEAD” in the Assembly section of this manual.
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Sneeuwmachine ST276EPT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Sneeuwmachine ST276EPT in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info