477703

Husqvarna Sneeuwmachine ST276EPT Manual

14
Zoom out
Zoom in
Previous page
1/76
Next page
14
Install traction drive control rod
The traction drive control rod (A) is installed on the snow thrower.
1. Remove plastic tie (B) securing rod to lower handle.
2. With top end of rod (A) positioned under left side of control panel, push
rod down and insert top end of rod into hole in drive control bracket (C).
Secure with retainer spring (D).
Installation des fahrantriebssteuerhebels
Die Steuerstange (A) für den Fahrantrieb muss am Schneeräumer montiert
werden.
1. Entfernen Sie das Kunststoffband, mit dem die Steuerstange am unteren
Griff befestigt ist.
2. Positionieren Sie das obere Ende der Steuerstange (A) unterhalb der
linken Seite der Bedienkonsole, drücken Sie die Steuerstange nach unten
und setzen Sie das obere Ende der Steuerstange in die Aussparung an
der Halterung der Antriebssteuerung ein (C). Arretieren Sie sie mit der
Sicherungsfeder (D).
Installez la tige de transmission du dispositif de
déplacement
La tige de commande de l’entraînement de la traction (A) est installée sur
la souffleuse à neige.
1. Retirer la fixation en plastique fixant la tige à la poignée du bas.
2. Avec l’extrémité supérieure de la tige (A) positionnée sous le côté gauche
du panneau de commande, abaisser la tige et insérer l’extrémité supéri-
eure de la tige dans le trou du support de la commande de l’entraînement
(C). Fixer avec le ressort de bague de retenue (D).
Montar la biela del mando de tracción
La varilla de transmisión de la tracción (A) está instalada en el quita-
nieves.
1. Retire la sujeción de plástico (B) que fija la varilla al asa inferior.
2. Coloque el extremo superior de la varilla debajo del lado izquierdo del
panel de control, empuje la varilla hacia abajo e introduzca dicho extremo
en el orificio del soporte del control de la transmisión (C). Asegure la
posición con el muelle de retención (D).
Het installeren van de regelstang van de aandrijving
met trekkabel
De regelstang van de tractieaandrijving (A) is op de sneeuwblazer geïn-
stalleerd
1. Verwijder de kunststof bevestigingsstang om de hendel omlaag te laten.
2. Als het uiteinde van de bovenkant zich onder de linkerkant van het
bedieningspaneel bevindt (A), dient u de stang omlaag te drukken en
het uiteinde van de bovenkant van de stang in de opening van de steun
van de aandrijfregeling te plaatsen (B). Bevestigen met klemveer (D).
Montaggio della barra di regolazione della trazione
La barra di comando dell’azionamento (A) di trazione è installata sul lancianeve.
1. Rimuovere la fascetta in plastica (B) che fissa la barra alla maniglia
inferiore.
2. Con l’estremità superiore della barra posizionata sotto il lato sinistro del
pannello dei comandi (A), spingere in basso la barra e inserire la sua
estremità superiore nel foro della staffa di comando dell’azionamento
(C). Fissare con l’apposita molla (D).
B
A
D
C
A
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Sneeuwmachine ST276EPT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Sneeuwmachine ST276EPT in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info