477694
37
Zoom out
Zoom in
Previous page
1/68
Next page
37
Adjusting the Control Cable
Checking the Control Cable
Release the control bar (1) to remove the slack in the control cable (2).
IMPORTANT: The control cable (2) must contain some slack when you
disengage the control bar (1) for the auger blades to stop properly.
NOTE: You may need to adjust the control cable (2) from position 1 (3)
(default) to position 2 (4) if you notice belt slip when the control bar (1)
is engaged.
NOTE: If the control cable (2) is adjusted to position 2, ensure that the
auger stops properly when the control bar (1) is released.
Adjusting the Control Cable
1. With the control bar (1) disengaged, unhook and move the con-
trol cable (2) to the highest position.
Einstellen der Steuerleitung
Prüfen der Steuerleitung
Lassen Sie die Steuerstange (1) los, so dass die Steuerleitung (2) nicht
mehr durchhängt.
WICHTIG: Die Steuerleitung (2) muss leicht durchhängen, wenn
Sie die Steuerstange (1) zum ordnungsgemäßen Auskuppeln der
Förderschneckenflügel loslassen.
HINWEIS: Wenn der Antriebsriemen bei gedrückter Steuerstange (1)
durchhängt, müssen Sie die Steuerleitung (2) unter Umständen von
Position 1 (3, Standardposition) in Position 2 (4) bringen.
HINWEIS: Wenn Sie die Steuerleitung (2) in Position 2 bringen,
vergewissern Sie sich, dass die Förderschnecke beim Loslassen der
Steuerstange (1) ordnungsgemäß zum Stillstand kommt.
Einstellen der Steuerleitung
1. Lassen Sie die Steuerstange (1) los. Hängen Sie die Steuerlei-
tung (2) dann aus und an der gewünschten Position wieder ein.
Réglage du câble de commande
Vérification du câble de commande
Relâchez la barre de commande (1) afin d’éliminer le ballant dans le
câble de commande (2).
IMPORTANT: Le câble de commande (2) doit présenter un peu de
ballant lorsque vous relâchez la barre de commande (1) de sorte à
permettre aux lames de la vis sans fin de s’arrêter correctement.
REMARQUE: Si vous remarquez un glissement de courroie lorsque
vous actionnez la barre de commande (1), vous devrez éventuellement
régler le câble de commande (2) et le déplacer de la position 1 (3)
(position par défaut) vers la position 2.
REMARQUE: Si vous placez le câble de commande (2) en position 2,
vérifiez que la vis sans fin s’arrête correctement lorsque vous relâchez
la barre de commande (1).
Réglage du câble de commande
1. Après avoir relâché le barre de commande (1), décrochez et
placez le câble de commande (2) à la position la plus haute.
1
1
2
4
3
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Sneeuwmachine ST 121E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Sneeuwmachine ST 121E in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 18,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info