477692
34
Zoom out
Zoom in
Previous page
1/48
Next page
32 Deutsch
WICHTIGE INFORMATION
Schneide und Halter werden am Fräsenrad
wie auf der Abbildung dargestellt montiert.
L = Linksmontage
R = Rechtsmontage
Achten Sie darauf, dass die Zähne in
Fräsrichtung zeigen.
Klinge, Halter und Zähne
demontieren und montieren
Rad entfernen und montieren
Demontieren Sie das linke Rad (8) der
Stubbenfräse, indem Sie den Befestigungssattel
(9), die 1/4"-Schrauben (1), die 1/4"-Sechs-
kantmuttern (3), die Federn (4) und den Bremsklotz
entfernen. Das Rad kann jetzt von der Achse
gezogen werden.
Demontieren Sie das rechte Rad (2), indem Sie den
Befestigungssattel (1) abnehmen und das Rad von
der Achse ziehen.
WARNUNG!
Die Schneide kann sich vom
Fräsenrad lösen, wenn die
Schrauben nicht fest genug
angezogen wurden. Beachten Sie
das empfohlene
Anzugsdrehmoment.
Halten Sie die Zähne (30, 31) auf der Position
gemäß der vorhergehenden Abbildung, in der die
Halter (32, 33) montiert werden. Gefahr durch
falsche Montage.
Führen Sie die Schraube (34) in einen Halter (32)
durch den Klingenteil (28) und durch den Halter
(33) nach außen zur anderen Seite.
Achten Sie darauf, dass der Spannstift an der
Hinterkante der Zähne an der Rückseite der Halter
anliegt. Dies ergibt eine korrekte Einstellung der
Schneidkante.
Ziehen Sie die Schrauben mit 162-203 Nm fest.
8011-215
8011-217
8011-216
PFLEGE
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna SG11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna SG11 in the language / languages: German as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna SG11

Husqvarna SG11 User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info