610269

Husqvarna Sappire 870 Quilt Manual

41
Zoom out
Zoom in
Previous page
1/48
Next page
41
4
1
2
Taking care of the machine
Changing the light bulbs
Your sewing machine is equipped with two light bulbs. One is
placed under the sewing head and one above the free arm. Only
use light bulbs of a type as indicated on the front of the machine
(24V, 5W). They are available at your authorized Husqvarna
Viking dealer. Change the light bulbs as described below.
Turn off the main switch.
1 Place the light bulb remover with the deep hole, marked
OUT, around the bulb. Do not turn the bulb, just pull it out
to remove it.
2 When inserting a new light bulb place the remover with the
shallow hole, marked IN, around the new bulb. Insert the new
bulb by pushing it up.
Cleaning the machine
To keep your sewing machine operating well, clean it often. No
lubrication (oiling) is needed.
Wipe the exterior surfaces of your sewing machine with a soft
cloth to remove any dust or lint built up.
Turn off the main switch.
Clean the Bobbin Area
Remove the presser foot and slide off the bobbin cover. Lower
the feed teeth. Place the screwdriver under the stitchplate as
shown on the picture and gently turn the screwdriver to pop off
the stitch plate. Clean the feed teeth with the brush.
Cleaning Under the Bobbin Area
After sewing several projects or any time you notice an
accumulation of lint in the bobbin case area, the area under the
bobbin case must be cleaned.
Remove the bobbin case holder (1) covering the front part of the
bobbin case. Remove the bobbin case (2) by lifting it up. Clean
with the brush. A small vacuum attachment works well to remove
dust and lint built up.
Put the bobbin case and the bobbin case holder back in place.
NOTE: Do not blow air into the bobbin case area. The
dust and lint will be blown into your machine.
Replacing the Stitch Plate
With feed teeth down, place the stitch plate about 5 mm (3/16)
in front of the rear edge and push it back. Slide on the bobbin
cover. Raise the feed teeth.
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Sappire 870 Quilt at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Sappire 870 Quilt in the language / languages: English as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info