518159
57
Zoom out
Zoom in
Previous page
1/64
Next page
Instruction book Rose
57
Incorrect stitch
If the machine does not sew the
stitch indicated by the display, it is
possible that the electronics have
been disturbed in some way, per-
haps by a short power cut or electri-
cal disturbance. Shut off the main
switch, wait a few seconds and try
again. If the fault remains, contact
your dealer.
The stitch is too loose - fabric
layers not held together
The thread tension is far too loose.
Page 14 shows how to adjust the
thread tension.
Fault-finding
Machine runs sluggishly
Dirt or lint has built up under the
stitch plate. Loosen the plate and
brush clean between the feed teeth
and in the bottom area. See page 55.
Balance setting for buttonhole
Balance can only be set if a button-
hole is selected. Press the buttons
and until the letters BAL
are flashing to the left on the dis-
play. In place of the stitch length
indication a balance indication is
shown. When you wish to increase
the density of the right column,
press stitch length button (-). When
you wish to decrease the density,
press stitch length button (+). The
balance can be set between -5 to +5.
The balance indication on the dis-
play will change in steps fo each
touch. When you select another
stitch, the display goes back to show
the sitch length indication. The
machine always retains the last
made balance setting.
Main motor does not work
The electronic overload protector
may have switched off. Shut off the
main switch, wait about a minute.
Then switch on the machine.
The sewing and embroidery
machine screen does not respond
to touch
The socket on the back of the
machine where the embroidery unit
is connected can be sensitive to
static electricity when the
embroidery unit is not connected. If
the sewing machine screen does not
respond to touch, turn the machine
off and back on again. If this
persists, contact your authorized
Husqvarna Viking retailer.
Expert assistance
Have your machine "tuned up"
regularly by your dealer. If you have
followed the preceding points and
still do not get satisfactory results,
you should contact the dealer where
you bought the machine. When the
machine is being checked, it is a
great help if it can be test sewn
under as similar conditions as
possible as when you used it.
Remember to take a sewing sample
along with you, preferably of the
fabric and with the thread you
intend to use.
A sewing sample will often give
much better information than words.
Non-original Parts and
Accessories
The warranty does not cover any
defect or damage caused by use of
non-original accessories or parts.
Fault-finding
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Rose 605 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Rose 605 in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info