579314
34
Zoom out
Zoom in
Previous page
1/63
Next page
Deutsch 33
WARTUNG
Bodendruck des Mähaggregats prüfen
und einstellen
Man erzielt ein optimales Mähergebnis, wenn das
Mähaggregat die Form des Rasens verfolgt, ohne
zu stark auf diesen zu drücken. Der Druck wird mit
je einer Schraube an den Seiten des Aufsitzmähers
eingestellt.
Vorgang bei der Einstellung des Bodendrucks:
1. Eine Badezimmerwaage unter die Vorderkante
des Aggregatrahmens stellen, so daß das
Aggregat auf der Waage ruht. Bei Bedarf kann
ein Holzklotz zwischen Rahmen und Waage
untergelegt werden, damit das Aggregat nicht auf
den Stützrädern ruht.
2. Den Bodendruck des Mähaggregats durch Ein-
oder Ausschrauben der Stellschrauben, die an
beiden Seiten hinter den Vorderrädern ange-
bracht sind, einstellen.
Der Bodendruck soll 12 bis 15 kg betragen.
2B
3
4
4
6
2A
7
8
5
Austausch des Schaltstifts (BioClip 103)
Um das BioClip-Aggregat und seinen Antrieb beim
Auffahren auf Hindernisse zu schützen, sind die
Messer mit einem Schaltstift ausgerüstet. An jedem
Messerbolzen befindet sich eine gewölbte federnde
Friktionsscheibe, die auszutauschen ist, wenn der
Messerbolzen gelöst wird. Wird sie nicht
ausgetauscht, kann der Schaltstift aktiviert werden
und eine Messerkollision verursachen. Nur
Originalteile verwenden. Ein Satz mit Messer,
Schaltstift und Friktionsscheibe ist beim Händler
erhältlich.
1. Aggregat in Servicestellung bringen, siehe
Aggregat in Servicestellung bringen.
2. Das Messer (2A) durch Entfernen des
Messerbolzen mit Scheibe und Friktionsscheibe
(2B) entfernen.
3. Reste des gebrochenen Schaltstifts (3)
entfernen.
4. Sicherstellen, dass die Anliegeflächen (4) von
Messer und Messerhalter metallisch rein sind.
Bei Bedarf säubern.
5. Neuen Schaltstift (5) in Messerhalter einbauen.
6. Messer (6) einbauen. Sicherstellen, dass das
Messer wie in der Abbildung gedreht ist.
7. Neue Friktionsscheibe (7) einsetzen. Die mit der
konkaven Seite muss zum Messer gewendet
sein.
8. Messerbolzen mit Scheibe (8) einbauen.
Anzugsmoment 45-50 Nm (4,5-5 kpm)
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Rider ProFlex 21 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Rider ProFlex 21 in the language / languages: German as an attachment in your email.

The manual is 3,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Rider ProFlex 21

Husqvarna Rider ProFlex 21 User Manual - Dutch - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info