467966
19
Zoom out
Zoom in
Previous page
1/132
Next page
7. Push the air filter into correct position.
8. Attach the air filter cover and tighten the knobs.
To examine and replace the spark
plug
1. Open the engine cover.
2. Remove the ignition cable shoe and clean around
the spark plug.
3. Remove the spark plug with a ⅝ʺ (16 mm) spark
plug wrench.
4. Examine the spark plug. Replace it if the electrodes
are burned or if the insulation has cracks or
damages. If the spark plug is not damaged, clean it
with a steel brush.
5. Measure the electrode gap and make sure that it is
correct. See
Technical data on page 29
.
6. Bend the side electrode to adjust the electrode gap.
7. Put the spark plug back in and turn it by hand until it
touches the spark plug seat.
8. Tighten the spark plug with the spark plug wrench
until the washer is compressed.
9. Tighten a used spark plug ⅛ of a turn more, and a
new spark plug ¼ turn more.
CAUTION:
Spark plugs that are not
tightened correctly can cause damage to
the engine.
10. Replace the ignition cable shoe.
CAUTION:
Do not try to start the engine
if the spark plug or ignition cable is
removed.
To replace the main fuse
A blown fuse is identified by a burned connector.
1. Open the engine cover. The main fuse is in a holder
in front of the battery.
2. Pull the fuse from the holder.
3. Replace the blown fuse with a new fuse of the same
type, flat pin 15 A.
4. Replace the covers.
If the main fuse blows again a short period after you
replace it, there is a short circuit. Repair the short circuit
before you operate the product again. Let an approved
service agent help you.
To replace a broken lamp
For R 216 only.
1. Remove the 2 screws and remove the lamp cover.
2. Disconnect the cables from the broken lamp.
854 - 003 - 14.11.2018
19
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Rider 216 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Rider 216 in the language / languages: English, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Rider 216

Husqvarna Rider 216 User Manual - German - 132 pages

Husqvarna Rider 216 User Manual - German - 32 pages

Husqvarna Rider 216 User Manual - Dutch - 132 pages

Husqvarna Rider 216 User Manual - Dutch - 32 pages

Husqvarna Rider 216 User Manual - French - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info