467966
10
Zoom out
Zoom in
Previous page
1/132
Next page
Explosive gases can come from the battery. Do not
smoke near the battery. Keep the battery away from
open flames and sparks.
Safety instructions for maintenance
WARNING: The product is heavy and can
cause injury or damage to property or the
adjacent area. Do not do maintenance on
the engine or the cutting deck without these
conditions:
The engine is off.
The product is parked on a level surface.
The parking brake is applied.
The ignition key is removed.
The cutting deck is disengaged.
The ignition cables are removed from the
plugs.
WARNING: The exhaust fumes from the
engine contain carbon monoxide, an
odourless, poisonous and very dangerous
gas. Do not run the product in closed spaces
or spaces with not sufficient air flow.
WARNING: Read the warning instructions
that follow before you use the product.
For best performance and safety, do maintenance
on the product regularly as given in the maintenance
schedule. See
Maintenance schedule on page 15
.
Electrical shocks can cause injuries. Do not touch
the cables when the engine is on. Do not do a
function test on the ignition system with your fingers.
Do not start the engine if the protective covers are
removed. There is a high risk of injury caused by
moving or hot parts.
Let the product become cool before you do
maintenance near the engine.
The blades are sharp and can cause cuts. Wind
protection around the blades or use protective
gloves when you do work on the blades.
Always put the cutting deck in servicing position to
clean it. Do not park the product near the edge of a
ditch or slope to get access to the cutting deck.
CAUTION: Read the caution instructions
that follow before you use the product.
Do not turn over the engine if the spark plug or
ignition cable is removed.
Make sure that all nuts and bolts are tightened
correctly and that the equipment is in good condition.
Do not change the adjustment of governors. If the
engine speed is too high, the product components
can become damaged. See
Technical data on page
29
for highest permitted engine speed.
The product is approved only with the equipment
supplied or recommended by the manufacturer.
Assembly
Introduction
WARNING: The drive belt tension spring
can break and cause injury. Wear protective
glasses when you attach or remove the
cutting deck.
Read the assembly instructions in the owner's manual
carefully. A label on the inner side of the front cover on
the product, also shows how to attach and remove the
cutting deck.
To remove and attach the cutting
deck
1. Park the product on level ground.
2. Apply the parking brake.
3. Set the cutting height lever in the servicing position.
4. Release the clip on the front cover with the tool
attached to the ignition key, and lift off the cover.
5. Lift the cutting height stay and put it in the holder for
the cutting height stay.
10 854 - 003 - 14.11.2018
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Rider 216 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Rider 216 in the language / languages: English, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Rider 216

Husqvarna Rider 216 User Manual - German - 132 pages

Husqvarna Rider 216 User Manual - German - 32 pages

Husqvarna Rider 216 User Manual - Dutch - 132 pages

Husqvarna Rider 216 User Manual - Dutch - 32 pages

Husqvarna Rider 216 User Manual - French - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info