579260
25
Zoom out
Zoom in
Previous page
1/32
Next page
English – 25
Lubrication
Checking the engine’s oil level.
Check the oil level in the engine when the Rider stands
horizontal with the engine switched off. Do not check the oil
with the engine running.
Open the engine cover.
Loosen the dipstick, pull it up and wipe it off.
The dipstick should be completely screwed down
Pull the dipstick out again and read the oil level.
The oil level should be between the markings on the dipstick.
The oil is topped up through the hole the dipstick sits in.
Fill the oil slowly. Tighten the dipstick correctly before starting
the engine. Start and run the engine at idling speed for
approx. 30 seconds. Turn off the motor. Wait 30 seconds and
check the oil level. If necessary fill so that the oil comes up to
the upper marking on the dipstick.
First and foremost use synthetic engine oil class SJ-CF 5W/
30 or 10W/30 for all temperature ranges. Mineral oil SAE30,
class SF–CC can be used at temperatures > +5 °C (40 °F)
Do not mix different types of oil.
Replacing the engine oil
The engine oil should be changed the first time after 8 hours
running time. It should then be changed after every 50 hours
of running time.
When operating with a heavy load or at high ambient
temperatures, replace every 25 hours.
1 Place a container underneath the engine’s left oil drain
plug.
2 Remove the dipstick. Remove the drain plug from the
engine’s left side.
3 Let the oil run out into the container.
4 Fit the drain plug and tighten it.
5 Fill the oil slowly. The oil is topped up through the hole the
dipstick sits in. See Checking the engine’s oil level for
filling instructions.
6 Run the engine warm, then check that there is no leakage
from the oil plug.
Lubricating the front wheel bearings
1 Remove the plastic cover that covers the centre of the
wheel.
2 Remove the circlip and washer on the front wheel axle.
3 Lift off the wheel.
4 Lubricate the stub axle with molybdenum disulphide
grease*.
5 Assemble the parts in the reverse order.
General lubrication
All joints and bearings are lubricated using molybdenum
disulphide grease during manufacture. Continue to lubricate
using the same type of grease *. Lubricate the steering and
control wires using engine oil.
Carry out this lubrication regularly.
*Grease from well-known brand names (petrochemical
companies, etc.) usually maintains a good quality. The most
important property is that the grease provides good
protection against corrosion.
!
WARNING! Engine oil can be very hot if it is
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
IMPORTANT INFORMATION
Used engine oil, antifreeze etc. is a health hazard and must
not be disposed of on the ground or in nature; it should
always be disposed of at a workshop or appropriate
disposal location.
Avoid skin contact; wash with soap and water in case of
spills.
IMPORTANT INFORMATION
Check that the circlip enters the groove correctly.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Rider 112C5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Rider 112C5 in the language / languages: English as an attachment in your email.

The manual is 5,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Rider 112C5

Husqvarna Rider 112C5 User Manual - German - 132 pages

Husqvarna Rider 112C5 User Manual - German - 32 pages

Husqvarna Rider 112C5 User Manual - Dutch - 132 pages

Husqvarna Rider 112C5 User Manual - Dutch - 32 pages

Husqvarna Rider 112C5 User Manual - French - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info