579260
22
Zoom out
Zoom in
Previous page
1/32
Next page
22 – English
Maintenance
Fuses
The main fuse is placed in a detachable holder behind the
battery under the protective cover.
Type: Flat pin, 15 A.
Do not use any other type of fuse when replacing.
A blown fuse is indicated by a burnt connector. Pull the fuse
from the holder when replacing.
The fuse is there to protect the electrical system. If it blows
again shortly after replacement, it is due to a short circuit,
which must be fixed before the machine can be put into
operation again.
Check the safety system
The machine is equipped with a safety system that prevents
starting or driving under the following conditions.
The engine can only be started when:
The cutting deck is raised and the parking brake is
applied.
The engine should stop when:
The cutting deck is lowered and the driver rises from the
seat.
The cutting deck is in its raised position, the parking brake
is not applied and the driver rises from the seat.
Check daily to ensure that the safety system works by
attempting to start the engine when one of the conditions
above is not met. Change the conditions and try again.
Checking the engine’s cooling air
intake
Clean the air intake grille in the engine cover behind the
driver’s seat.
Open the engine cover.
Check that the cooling intake is free from leaves, grass and
dirt.
A blocked cooling intake will interfere with the cooling of the
engine, which can damage the engine.
Service position for the cutting unit
The cutting deck can be removed in order to facilitate cleaning
and servicing.
To remove the cutting deck proceed as follows:
1 Position the machine on flat ground.
2 Apply and lock the parking brake.
3 Rider 112C has the brake pedal and lock button on the
left hand side. (1) Rider 112C5 has the brake pedal and
lock button on the right hand side. (2)
!
WARNING! Do not modify safety equipment.
Check regularly that they function as they
should. The machine must not be run with
defective or disassembled safety equipment.
!
WARNING! The cooling air intake rotates
when the engine is running. Mind your
fingers.
IMPORTANT INFORMATION
Avoid cutting when the cutting head is placed in service
position, to prevent damaging to the drive belt.
!
WARNING! Exercise caution when handling
the spring. Wear protective glasses when
fitting the cutting unit.
1
2
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Rider 112C5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Rider 112C5 in the language / languages: English as an attachment in your email.

The manual is 5,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Rider 112C5

Husqvarna Rider 112C5 User Manual - German - 132 pages

Husqvarna Rider 112C5 User Manual - German - 32 pages

Husqvarna Rider 112C5 User Manual - Dutch - 132 pages

Husqvarna Rider 112C5 User Manual - Dutch - 32 pages

Husqvarna Rider 112C5 User Manual - French - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info