684090
32
Zoom out
Zoom in
Previous page
1/152
Next page
Problem Cause
There is vibration in the product The collector is full. The operator has ignored the collector full signal or the sen-
sor for collector full is set in the incorrect position. See
To adjust the sensor for
collector full on page 16
.
The product is operated in long, thick and/or wet grass in non-collect mode. See
To get a good mowing result on page 18
.
The blades are loose. See
To examine the blades on page 28
.
One or more of the blades are unbalanced. See
To examine the blades on page
28
.
The auger is damaged.
The engine is loose.
The mowing result is unsatisfac-
tory
The blades are blunt. See
To replace the blades on page 28
.
The grass is long or wet. See
To get a good mowing result on page 18
.
The cutting deck is skew.
There is grass blockage in the cutting deck. See
To clean the product on page
20
.
The tire pressure is different on the right and left sides. See
To set the tire pres-
sure on page 25
.
The product is operated at a too high speed. See
To get a good mowing result
on page 18
.
The engine speed is too low. See
To get a good mowing result on page 18
.
The drive belt slips.
Transportation, storage and disposal
Transportation
The product is heavy and can cause crush injuries.
Be careful when you load it onto or off a vehicle or
trailer.
Use an approved trailer for transportation of the
product.
Make sure that you have knowledge of local road
traffic regulations before transportation of the
product in a trailer or on roads.
To safely attach the product on a trailer for
transport
WARNING: The parking brake is not
sufficient to lock the product during
transport. Attach the product tightly to the
trailer.
Equipment: 2 approved tension belts and 4 wedge
shaped wheel blocks.
1. Apply the parking brake.
2. Attach the tension belts around the frame or rear
wagon.
3. Tighten the tension belts in the direction of the rear
and the front of the trailer to secure the product.
4. Put the wheel blocks in front of and behind the rear
wheels.
To tow the product
The product has a hydrostatic transmission. To prevent
damage to the transmission, tow the product short
distances only and at low speed.
Disengage the transmission when you tow. See
To
engage and disengage the drive system on page 15
.
Storage
Prepare the product for storage at the end of the
season, and before more than 30 days of storage. If you
keep fuel in the fuel tank for 30 days or more, tacky
particles can cause blockage in the carburetor. This has
a negative effect on the engine function.
32 368 - 004 -
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna RC 318T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna RC 318T in the language / languages: English, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna RC 318T

Husqvarna RC 318T User Manual - German, Dutch, French - 156 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info