684090
25
Zoom out
Zoom in
Previous page
1/152
Next page
CAUTION: To prevent short circuit,
make sure that the red cable from
the battery charger is connected to
the correct solenoid.
4. Connect the black cable (-) from the battery charger
to a zinked metal part as shown in the illustration (3).
WARNING: The battery and
electrical system can become
damaged and cause injuries if
incorrect type of charger is used.
Use only the charger specified by
Husqvarna for this type of battery
(LiFePO4).
5. Start the battery charger.
Note: If the battery voltage is too low the battery
goes into protective mode. The battery charger
can not sense the battery and does not charge.
If this occurs, press and hold the reset button on
the battery charger for 10 seconds until it starts
to charge. Read more in the instructions that are
supplied with the battery charger.
6. When the battery is charged, stop the charger and
disconnect it from the battery.
7. Put the rubber cap (1) back on the solenoid.
To set the tire pressure
The correct tire pressure is 150 kPa (1.5 bar / 21.8 PSI)
on all 4 tires.
To put the cutting deck in servicing
position
1. Park the product on level ground.
2. Apply the parking brake.
3. Set the cutting height lever in the servicing position.
4. Pull the lift lever for the cutting deck rearward to its
locked position to lift up the cutting deck.
5. Lower the auger control lever to lift the auger to
servicing position.
6. Release the clip on the front cover with the tool
attached to the ignition key, and lift off the cover.
7. Pull the spring handle (1) to the right out from the
spring holder to loosen the drive belt tension.
8. Hold the spring handle with your left hand and lift off
the drive belt with your right hand.
9. Put the drive belt in the belt holder (2).
10. Put the spring handle in the spring holder to prevent
that the spring falls down.
11. Lift the cutting height stay and put it in the stay
holder. (3)
1
3
2
368 - 004 - 25
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna RC 318T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna RC 318T in the language / languages: English, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna RC 318T

Husqvarna RC 318T User Manual - German, Dutch, French - 156 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info