733964
30
Zoom out
Zoom in
Previous page
1/168
Next page
2. Remove the nut on the oil drain plug.
3. Remove the dipstick.
4. Let the oil run out into the container.
5. Push the oil drain plug in and turn it clockwise to
close it.
6. Attach the nut on the oil drain plug.
7. Turn the oil filter counterclockwise to remove it.
8. Lightly lubricate the rubber seal on the new oil filter
with new oil.
9. To attach the oil filter, turn it clockwise until the
rubber seal is in position, then tighten a half turn
more.
10. Fill with new oil as given in
Technical data on page
37
.
11. Start the engine and let it run at idle speed for 3
minutes.
12. Stop the engine and make sure that the oil filter does
not leak.
13. Do a check of the engine oil level. Refer to
To do a
check of the engine oil level on page 28
.
14. Fill with oil to the FULL mark on the oil dipstick.
Note: For safe disposal of used engine oil, refer to
Disposal on page 36
.
To do a check of the transmission oil
level
WARNING: Do the transmission oil check
when the transmission is cool.
1. Remove the 2 screws, and remove the transmission
cover.
2. Make sure that the oil level in the transmission oil
tank is between the 2 horizontal lines on the tank.
Min
Max
3. Fill with engine oil if the oil level is below the lower
line, but do not fill above the top line. Refer to
Technical data on page 37
for recommended oil.
Lubrication, general information
Remove the ignition key to prevent accidental
movements during lubrication.
Use engine oil when you lubricate with an oil can.
When you lubricate with grease, use a chassis or
ball bearing grease that prevents corrosion. Remove
unwanted grease after lubrication.
Lubricate 2 times a week if you operate the product
daily.
Do not spill lubricant on the drive belts or the
grooves of the belt pulleys. If you do spill, clean with
alcohol. If the friction between the drive belt and the
pulley is not sufficient after you clean with alcohol,
replace the drive belt.
CAUTION: Do not use gasoline or other
petroleum products to clean drive belts.
To lubricate the throttle cable, choke
cable and lever bearings
1. Remove the right side cover.
2. Open the engine cover.
30 880 - 002 - 28.02.2019
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna R 420TsX AWD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna R 420TsX AWD in the language / languages: English, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 11,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna R 420TsX AWD

Husqvarna R 420TsX AWD User Manual - German, Dutch, French - 172 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info